Bedienungsanleitung Ruby Fires bio burner (Seite 6 von 16) (Deutsch, Englisch, Holländisch, Französisch)

531519

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Filling the ceramic burner with Ruby Fires bio ethanol 98% LEF, use only LEF to ﬁll the ceramic burner.

• It is of great importance that the liquid never ﬂows outside the ﬁlling opening.

• Make sure to ﬁll the ceramic burner carefully and slowly, so it cannot be overﬁlled.

• In case liquid is spilled, use a soft, absorbing cloth to clean.

• For an optimal ﬁre the burner has to be ﬁlled not higher than 1 cm below the surface of the ceramic element.

When the ceramic burner is ﬁlled with LEF for the ﬁrst time, the ceramic element on the inside will be saturated completely. The liquid

will always remain partly absorbed by the brick. Therefore it is necessary to use more bio ethanol the ﬁrst time the burner is ﬁlled than

the following times.

First ﬁlling Reﬁll

Ceramic burner Mini (4114) ± 1 liter ± 0.8 liter

Ceramic burner Small (4120 + Silo) ± 1.5 liter ± 1 liter

Ceramic burner Big (5820) ± 2 liter ± 1,5 liter

Ceramic line Burner (8014) ± 2,5 liter ± 2 liter

How to ﬁll the ceramic burner:

• Open the latch for one third, so the ﬁlling-opening is visible. With square burner: open fully.

• Place the enclosed funnel in the ﬁlling-opening.

• Carefully pour the Ruby Fires bio ethanol 98% in the funnel until the ceramic brick is saturated, but make sure that the liquid level

remains underneath the surface of the element: at least 1 cm!

• Warning: Make sure that the liquid does not ﬂow outside the ﬁlling-opening. In case liquid has been spilled outside the ﬁlling-

opening, make sure this is dried up before lighting the ﬁre. Risk of ﬁre! There should never be ﬁre outside the ﬁre-opening. This is

dangerous and can also cause the insert to de-form and damage of the paint of the insert.

• Warning: Keep on ﬁlling the burner until the level remains visible in the ﬁlling-opening. The level must remain at least 1 cm

underneath the surface.

• When the ceramic burner is ﬁlled, remove the funnel. You can now fully open the latch. The burner-opening is visible and the

ceramic burner is ready for use.

Latch open Latch closed

How to re-ﬁll the ceramic burner:

• Close the latch when the ceramic burner is burnt empty.

• Check carefully that there is no longer any ﬁre on the surface.

• Warning: Never ﬁll a burning burner – Life threatening!

• Wait at least 30 minutes for the Bio Flame Burner to cool down.

• For further instructions see: ‘How to ﬁll the ceramic burner”

Lighting the ceramic burner:

• There is a latch for the ﬁre-opening on the topside of the ceramic burner.

• When the ceramic burner is not lit, this latch is closed (to prevent the bio ethanol from evaporating).

• By opening the latch the ﬁre-opening with the ceramic brick becomes visible.

• The ceramic burner can be lit using a long lighter or a long matchstick, but only when nothing is placed on the opening and the

Ruby Fires bio ethanol 98% is well ﬁlled as described in: ‘How to ﬁll the ceramic burner’

LEF

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ruby Fires bio burner Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info