Bedienungsanleitung Ruby Fires TT5400 (Seite 4 von 12) (Deutsch, Englisch, Holländisch, Französisch)

531524

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

- 1 - IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

Important Safety Advice

When using electrical appliances, basic precautions

should always be followed to reduce the risk of re,

electrical shock, and injury to persons, including the

following:

If the appliance is damaged, check with the supplier before

installation and operation.

Do not use this heater in the immediate surroundings of

a bath, shower or swimming pool.

Do not locate the heater immediately below a xed socket

outlet or connection box.

Do not cover or obstruct in any way the heat outlet grille

located at the top of the heater or the heat outlet at the

base of the heater. Overheating will result if the heater is

accidentally covered.

This appliance is not intended for use by children or other

persons without assistance or supervision if their physical,

sensory or mental capabilities prevent them from using it

safely. Children should be supervised to ensure that they

do not play with the appliance.

In the event of a fault unplug the heater.

Unplug the heater when not required for long periods.

Ensure that furniture, curtains or other combustible

material are positioned no closer than 1 metre from the

heater.

Although this heater complies with safety standards, we

do not recommend its use on deep pile carpets or on long

hair type of rugs.

The appliance must be positioned so that the plug is

accessible.

Do not use this heater in series with a thermal control,

a program controller, a timer or any other device that

switches on the heat automatically, since a re risk exists

when the heater is accidentally covered or displaced.

If the supply cord is damaged it must be replaced by the

manufacturer or service agent or a similarly qualied

person in order to avoid a hazard.

Caution: In order to avoid a hazard due to inadvertent

resetting of the thermal cut-out, this appliance must not

be supplied through an external switching device, such

as a timer, or connected to a circuit that is regularly

switched on and off by the utility.

The heater carries the Warning symbol indicating

that it must not be covered.

General

Unpack the heater carefully and retain the packaging for possible

future use, in the event of moving or returning the re to your

supplier. Screws and rawl plugs, a remote control and batteries

are packed separately within the carton.

This re incorporates a ame effect which can be used with or

without heating, so that comforting effect may be enjoyed at any

time of the year. The ame effect is provided by a low wattage

motor and three 60 watt lamps. Using the ame effect on its own,

therefore, requires little electricity.

The controls are located at the bottom right hand corner of the

appliance (see ‘z’ in Fig. 1). A choice of 750W or 1500W heat

output is provided by the fan heater, which is concealed at the top

of the heater (see ‘y’ in Fig. 1).

Please note: Used in an environment where background noise

is very low, it may be possible to hear a sound which is related to

the operation of the ame effect. This is normal and should not

be a cause for concern.

Electrical connection

WARNING – THIS APPLIANCE MUST BE EARTHED.

This heater must be used on an AC ~ supply only and the voltage

marked on the heater must correspond to the supply voltage.

Before switching on, please read the safety warnings and operating

instructions.

Installation

Do not connect appliance until properly xed to the wall and the

instruction leaet is read fully.

The minimum distances must be observed.

For installation of the appliance, care must be taken not to

damage concealed cables.

Please be careful while drilling holes.

This model is designed to be permanently xed to a wall at a

minimum height of 300mm. The top wall bracket must be tted

horizontally and the cable routed to the bottom of the heater.

A height of 550mm from the bottom of the heater to oor is

recommended for optimum viewing of the fuel bed (see Fig. 1 for

recommended xing dimensions).

For optimum viewing mark the top four screw xing positions on

wall in accordance with the recommended xing dimensions

(see Fig. 2a).

Drill holes with a 6mm drill bit.

Fix the bottom bracket to the appliance using the 2 black self

tapping screws provided (see Fig. 2b).

Fix the top wall bracket using the plugs and screws provided

(see Fig. 2c).

Carefully lift the heater up ensuring that the rear ledge of the heater

engages the top wall bracket and is sitting centrally positioned on

the bracket.

Mark the bottom bracket hole positions (see Fig. 2d) and remove

the heater.

Drill holes with a 6mm drill bit and insert plugs (see Fig. 2e).

Ret the heater to the wall xing bracket and use the screws

provided to permanently x the heater.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ruby Fires TT5400 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info