Bedienungsanleitung Rupes PL824V (Seite 6 von 28) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

489895

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

easily, place the front groove of the centre of the

planer shoe onto the workpiece edge and guide

the planer forward evenly, maintaining an angle

of 45º (Fig. 4).

6. CHIPS OUTLET

The chips outlet can be shifted to the right (nor-

mal position) or left by placing the lever L(Fig. 1)

facing the side you have selected.

The connection of the planer to a collector is car-

ried out by means of the collector.

ARNING! The external collector attachment

must never be set up on the machine if no collec-

tor is used. This would prevent the free ejection

of chips.

7. BRAKE FOR BLADE-HOLDER

The planer comes equipped with a mechanical

centrifugal brake that reduces the time taken

from switch disconnection to stopping the blade-

holder down to less than 10 seconds.

Foryourown safety, should you notice that more

time is needed to stop, have the brake replaced

at a RUPES technical service outlet.

8. REST SHOE

The S rest shoe for the planer (Fig. 11) enables

you to park the machine immediately after a work

operation with no risk of damage to the workpla-

ce surface or the planer blades.

Forthe next work operation, the rest shoe swings

up out of the way, thus allowing the planer to

slide all along its base.

9. REPLACING AND CONTROLLING

THE BLADES

WARNING! Always remove the plug from the

mains socket before carrying out this operation.

a) REPLACING STANDARD BLADES

To replace standard blades or invert them to use

their reverse head, proceed as follows: Loosen

the three locking screws M (Fig. 5) using the

open-end spanner in a clockwise direction.

Lower the blade-holder protective device N (Fig.

5, 6) to obtain enough place and to move the

blade-holder sideways.

Remove the blade and replace it with a new one

or reinsert the same blade with the reverse head.

Reinsert the support with the blade into the blade

holder, checking with the help of a rule that the

fixed blade head O (Fig. 7) is level with the rule

and does not jut out. Tighten the screws M (Fig.

5) in counter-clockwise direction with the open-

end spanner

Remove any dust and resin from the seats of the

blade-holder and supports before inserting new

blades.

BLADE REGULATION

Blade supports are regulated before leaving the

factory and do not require readjustment when

changing the blade. Nonetheless, if for any rea-

son they have to be adjusted, do so as follows:

Loosen screws M (Fig. 5) slightly with the open-

end spanner in clockwise direction.

Place a rule over the base and loosen the screws

P (Fig. 8) of the blade support to raise it or con-

ceal it until it is perfectly on a level with the rule.

Verify this adjustment in two points near the end

of the blade.

Check that the side head of the blade O (Fig. 7)

is level with the rule and does not jut out. Tighten

the screws M (Fig. 5) in counter-clockwise direc-

tion with the open-end spanner.

b) REPLACING HSS 3-MM STRAIGHT

BLADES

The procedure for replacing straight blades is

identical to that given in section A). The only dif-

ference is that here it is necessary to regulate the

blade height (See Figs. 12 to 19).

c) REPLACING HSS 3-MM RUSTIC BLADES

The procedure for replacing rustic blades is iden-

tical to that given in section A). The only differen-

ce is that here the blades require additional verti-

cal adjustment (See Figs. 20 to 27).

ARNING! The lowest point of the rustic blade

must not jut out from the planer base. See (Fig.

25).

ARNING! After any blade change, ensure that

the 6 clamping screws M (Fig. 5) are tightly scre-

wed down before starting up the planer again.

When replacing the blade-holders, use only ori gi

nal RUPES components.

10. CHANGING THE TRANSMISSION BELT

WARNING! Always remove the plug from the

mains socket before carrying out any work on the

machine.

Remove the protective cover Q (Fig. 4) by loose

ning the 2 screws that hold it in place. Cut the

worn toothed belt with pliers or a knife and remo-

ve.

Clean the pulley and the driving wheel carefully

before replacing the belt with another original

RUPES belt.

Assemble the toothed belt (fig. 9), turning it

clockwise while simultaneously moving it towards

the inside. Be careful to mesh it correctly with the

teeth of the pulley without forcing it.

librettoPL824 30-03-2007 14:57 Pagina 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rupes PL824V Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info