Bedienungsanleitung Russell Hobbs 25600-56 (Seite 5 von 100) (Alle Sprachen)

705952

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

• To rell at any time during use, turn the steamer o by pressing the power button until the blue

indicator light goes out, unplug from outlet, and follow the above procedure.

• After relling, allow to reheat for 45 seconds and then prime the pump by holding the steam trigger

until steam forms.

USING

• If the label says “do not iron” or shows this icon i, t the delicate attachment and make sure to test

on an inconspicuous area prior to steaming the entire garment.

• If the label says “do not steam” or shows this icon m, do not steam the garment.

1. Hang the garment in an area that will not be aected or damaged by the heat and steam, such as on

a shower curtain rail, or in an open doorway.

2. Fit any attachment you wish to use.

3. Plug the steamer in then press the power button. The blue power button light will slowly ash,

indicating that the steamer is heating.

4. After about 45 seconds the power light will stay on, indicating the steamer is preheated.

5. Prime the water pump by holding steam trigger until steam forms.

6. To generate steam, press the steam trigger. As long as the trigger is held, steam will emit from the

steamer. When the trigger is released, the steam will stop.

7. To generate a constant ow of steam without holding the trigger, press the steam trigger and then

slide the steam trigger lock downwards. You can then release pressure on the steam trigger. To turn

the steam o, press the trigger, slide the steam trigger lock upwards, then release the trigger.

8. With your free hand keep the fabric taut. Steam the garment with slow, downward strokes, keeping

the head of the steamer in contact with the fabric.

9. When you have nished, press and hold the power button until the blue light goes out (about 3

seconds) and unplug.

10. Stand the steamer on its base and allow it to completely cool o before storing. To avoid mineral

buildup, empty the tank after each use.

Auto shut o

Your steamer will automatically switch to auto shut-o mode after being left inactive for 15 minutes. The

power button light will ash rapidly to indicate this. To resume steaming, press the steam trigger or power

button and wait for your steamer to fully reheat.

CARE AND MAINTENANCE

1. Make sure steamer is o, unplugged and completely cool.

2. Wipe all surfaces with a clean damp cloth.

3. After the steamer has been thoroughly dried, turn it back on and lightly steam over an old cloth. This

will help remove any residue left in the steam holes.

4. To avoid mineral buildup, empty the tank after each use.

Cleaning attachments

• Lint attachment: Wipe with damp cloth to clean.

• Delicate fabric attachment: Wash with cold water and small amounts of a gentle cleanser if needed.

The fabric cannot be removed.

• Upholstery attachment: The fabric can be removed and hand washed with cold water and a gentle

cleanser.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Russell Hobbs 25600-56 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info