Bedienungsanleitung Ryobi CHI-1442 (Seite 15 von 142) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

491254

Zoom out

Zoom in

Vorherige Seite

1/142

Nächste Seite

OPERATION

■ Connect charger to power supply.

■ Place battery pack in charger. Align raised rib on

battery pack with groove in charger.

■ Press down on battery pack to be sure contacts on

battery pack engage properly with contacts in charger.

When properly connected, red light will turn on.

■ When your battery pack becomes fully charged, the

red light will turn off and the green light will turn on.

■ After normal usage, 1 hour of charge time is required

to be fully charged. A minimum charge time of 1 to

1-1/2 hours is required to recharge a completely

discharged tool.

■ DO NOT place charger in an area of extreme heat

or cold. It will work best at temperatures above 10°C

and below 38°C

IMPORTANT INFORMATION FOR RECHARGING HOT

BATTERIES

When using your tool continuously, the batteries in your

battery pack will become hot. You should let a hot battery

pack cool down for approximately 30 minutes before

attempting to recharge.

TO INSTALL BATTERY PACK (Fig.2)

■ Place the direction of rotation selector in center

position.

■ Place the battery pack in the tool. Align raised rib on

battery pack with groove in the tool’s battery port.

■ Make sure the latches on each side of the battery

pack snap in place and that battery pack is secured in

the tool before beginning operation.

TO REMOVE BATTERY PACK (Fig.2)

■ Place the direction of rotation selector in center

position.

■ Locate latches on side of battery pack and depress

both sides to release battery pack.

■ Remove battery pack from the tool.

SWITCH TRIGGER (Fig.3)

■ To turn the drill ON, depress the switch trigger.

■ To turn it OFF, release the switch trigger.

VARIABLE SPEED

The variable speed switch trigger delivers higher speed

and torque with increased trigger pressure and lower

speed with decreased trigger pressure.

SWITCH LOCK (Fig. 3)

The switch trigger can be locked in the OFF position.

This feature can be used to prevent the possibility of

accidental starting when not in use. To lock switch trigger,

place the direction of rotation selector (Forward/Reverse

Selector) in center position.

Note: When selector is in center position, switch trigger

is locked.

REVERSIBLE (Fig. 3)

The direction of bit rotation is reversible and is controlled

by a selector located above the switch trigger. With the

drill held in normal operating position, the direction of

rotation selector should be positioned to the left of the

switch trigger for drilling. The drilling direction is reversed

when the selector is to the right of the switch trigger. To

stop the drill, release the switch trigger and allow the

chuck to come to a complete stop.

ADJUSTING THE SPEED (Fig. 4)

Follow these steps to adjust the speed.

■ For high speed: Slide the two-speed gear train switch

to “2”.

■ For low speed: Slide the two-speed gear train switch

to “1”.

Note: If you have difficulty changing from one gear

range to the other, turn the chuck by hand until the gears

engage.

CAUTION

To prevent gear damage, always allow chuck to

come to a complete stop before changing the

speed or the direction of rotation.

QUICK MODE SELECTOR (CHD-1442/CHP-

1802 Fig.5 / CHI-1442/CHI-1802 Fig.6)

The Quick Mode Selector allows you to quickly switch

from drill mode to drive mode.

In general, drill mode should be used for drilling and

other heavy duty applications. Drive mode should be

used for driving screws. Impact mode should be used for

impact drilling.

English

E I

P NL

S DK N FIN GR

H CZ RUS PL

SLO TR

960931224-01B.indd 11960931224-01B.indd 11 7/20/07 11:16:39 AM7/20/07 11:16:39 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ryobi CHI-1442 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info