Bedienungsanleitung Ryobi crp 1801 (Seite 8 von 73) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

383633

Zoom out

Zoom in

Vorherige Seite

1/73

Nächste Seite

PRODUCT SPECIFICATIONS

18V

Blade Stroke 22 mm

Motor 18 V

Maximum Cutting Thickness (wood) 60 mm

No Load Speed 0-3000 min

-1

Switch Variable Speed

FEATURES

1. LOCK-OFF BUTTON

2. DEPRESS HERE TO PULLSWITCH TRIGGER

3. SWITCH TRIGGER

4. BLADE CLAMP LOCK / RELEASE LEVER

5. SAW BLADE

6. BASE (SHOE) ASSEMBLY

7. BATTERY PACK (NOT INCLUDED)

8. LATCHES

9. DEPRESS LATCHES TO RELEASE

BATTERY PACK

10. BLADE CLAMP

11.TON INSTALL/TO RELEASE

12. TO LOCK

13. BLADE SHOWN CORRECT IN SAW BAR

OPERATION

WARNING

Always remove battery pack from your saw when

you are assembling parts, making adjustments,

assembling or removing blades, cleaning,

or when not in use. Removing battery pack will

prevent accidental starting that could cause

serious personal injury.

TO REMOVE / ATTACH BATTERY PACK

(NOT INCLUDED)

See Figure 2.

TO REMOVE

■ Locate latches on side of battery pack and depress

both sides to release battery pack from your saw.

■ Remove battery pack from your saw.

TO ATTACH

■ Place the battery pack in your saw aligning raised rib

on battery on battery pack with groove in saw's

battery port. See figure 2.

■ Make sure the latches on each side of the battery

pack snap into place and battery pack is secured to

saw before beginning operation.

TO INSTALL SAW BLADE

See Figure 3.

■ Remove battery pack. See figure 2.

WARNING

Failure to remove battery pack from saw could

result in accidental starting causing possible

serious personal injury.

■ Lift blade clamp lock/release lever on side of saw.

■ Insert saw blade between blade clamp and saw bar.

■ Lock blade clamp lever.

■ Replace battery pack.

GENERAL CUTTING

See Figure 4.

Hold your saw firmly in front of and clearly away from you.

Make sure saw blade is clear of any foreign material.

Be sure material to be cut is held firmly. Small work pieces

should be securely clamped in a vise or with clamps to

the work bench or table. Mark the line of cut clearly.

Depress the lock-off button, then pull switch trigger to start

the cutting action. Place the base assembly against the

work, then move the blade into the work. Do not force.

Use only enough pressure to keep the saw cutting.

Let the blade and saw do the work. Use of excessive

pressure that causes bending or twisting of the blade

may result in broken blades.

PLUNGE CUTTING

See Figure 5.

Mark the line of cut clearly. Choose a convenient starting

point inside the area to be cut out and place the tip of the

blade over that point. Rest front edge of base assembly

on work and hold firmly in position. Depress the lock-off

button, then pull switch trigger to start the cutting action.

WARNING

Make sure blade does not touch work until motor

reaches full speed, since this could cause loss of

control resulting in serious injury.

With saw blade at full cutting speed, slowly tilt saw

downward until tip of blade starts cutting work.

After blade penetrates work, tilt saw until blade is

perpendicular to the work.

English

F D E I P NL S DK N FIN GR H CZ RUS PL

SLO TR

CRP-1801DM 10/05/05 11:38 Page 5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ryobi crp 1801 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info