Bedienungsanleitung Ryobi css 1801m one (Seite 14 von 137) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

383100

Zoom out

Zoom in

Vorherige Seite

1/137

Nächste Seite

SPECIFIC SAFETY RULES

■ Do not charge battery tool in a damp or wet

location. Following this rule will reduce the risk of

electric shock.

■ For best results, your battery tool should be

charged in a location where the temperature is

more than 10°C but less than 38°C. Do not store

outside or in vehicles.

■ Under extreme usage or temperature conditions,

battery leakage may occur. If liquid comes in

contact with your skin, wash immediately with

soap and water, then neutralize with lemon juice

or vinegar. If liquid gets into your eyes, flush them

with clean water for at least 10 minutes, then seek

immediate medical attention. Following this rule will

reduce the risk of serious personal injury.

SPECIFICATIONS

Motor 18 V

Switch On/Off Switch

No load speed 22,500 min

-1

Collet 6.35 mm

Collet Adaptor 3.2 mm

Battery pack (not included) BPP-1815M/BPP-1817M

Charger (not included) BC-1800/BC/1815-S

FEATURES

1. Switch

2. Spindle Lock

3. Depth Adjustment Ring

4. Collet Nut

5. Adjusting Knob

6. Bit

7. Tab

8. Wrench

9. Screw

10. Nut

11. Handle

12. Pivot Point Knob

13. Threaded Ring

14. Circle Cutter Arm

15. Adaptor

16. Battery Pack (Not included)

17. Latches

18. On

19. Off

20. Tighten

21. Loosen

22. Adjust up or down

ASSEMBLY

REMOVING DEPTH ADJUSTMENT RING (Fig. 2)

■ Remove battery pack from spiral saw.

■ Place wrench in tab on depth adjustment ring.

■ Depress spring-loaded tab.

■ Lift depth adjustment ring off tool.

ASSEMBLING CIRCLE CUTTER (Fig. 3)

■ Remove battery pack from spiral saw.

■ Attach handle with screw provided.

■ Attach pivot point knob with nut provided.

ATTACHING CIRCLE CUTTER (Fig. 4)

■ Remove Battery Pack From spiral saw.

■ Assemble circle cutter if necessary. Refer to

“Assembling Circle Cutter.”

■ Remove bit if necessary. Refer to “Inserting/

Removing Bits” in this manual.

■ Place adaptor under depth adjustment ring.

Note: Make sure the adaptor fits snugly.

■ Place circle cutter arm on top of depth adjustment

ring.

■ Screw threaded ring onto adaptor, securing circle

cutter arm.

■ Insert bit. Refer to “Inserting/Removing Bits” in

this manual.

OPERATION

WARNING

Do not allow familiarity with tools to make

you careless. Remember that a careless fraction

of a second issufficient to inflict serious injury.

WARNING

Always wear safety goggles or safety glasses

with side shields when operating tools. Failure to

do so could result in objects being thrown into

your eyes, resulting inpossible serious injury.

WARNING

Do not use any attachments or accessories not

recommended by the manufacturer of this tool.

The use of attachments or accessories not

recommended can result in serious personal

injury.

English

F D E I P NL S DK N FIN GR H CZ RUS PL

SLO TR

CSS-1801DM 29/07/05 10:52 Page 10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ryobi css 1801m one Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info