Bedienungsanleitung Ryobi eag 8512 r (Seite 8 von 70) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

391211

Zoom out

Zoom in

Vorherige Seite

1/70

Nächste Seite

DESCRIPTION

5. ON / OFF switch

6. Lock-on feature

7. Disc flange

8. Clamp nut

9. Spindle shaft

10. Wrench

11. Spindle lock button

12. Wheel guard lock lever

13. Live tool indicator

STANDARD ACCESSORIES

Aux. handle (3).

A grinding wheel is included in the standard accessories

for some countries.

APPLICATION

Use only for the purpose listed below:

- Grinding

NOISE BUILD-UP

Noise (sound pressure level) in the workplace can exceed

85 dB (A). In this case, sound insulation and hearing

protection measures must be taken by the operator.

ON / OFF SWITCH

■ To switch on the unit – use your index finger to

depress the on / off switch (5).

■ To switch off the unit – just release the on / off

switch (5).

LOCK-ON FEATURE (FIG. 1)

Your grinder has a lock-on feature that is convenient when

continuous operation over an extended period of time is

required. To lock-on, depress the on / off switch and push

in the safety lock located on the side of the handle.

While holding the safety lock pushed in, release the switch.

To release the lock, depress the switch and release it.

MAIN HANDLE

The main handle can be set to any of three positions

(0 and 90 degree right and left) by pressing the rotary

lock button (4).

TOOL-LESS WHEEL GUARD

Release the wheel guard lock lever (12) then turn the

tool-less wheel guard (2) to the desired position.

The max. turning axle is 90º on either side; otherwise the

guard can’t be locked.

MOUNTING THE GRINDING WHEEL

■ Attach the disc flange (7), the grinding wheel (1) and

the clamp nut (8) to the spindle shaft (9).

■ Be sure that the disc flange is properly seated on the

spindle shaft.

■ Depress the lock button (11) located on the right side

of gear case.

■ Using the wrench (10) provided, tighten the clamp nut

in a clockwise direction.

WARNING

Check carefully whether or not there are

cracks in the wheel. Replace a cracked wheel

immediately.

OPERATING (FIG. 3)

KEEP SAFETY GUARDS IN PLACE.

NEVER COVER THE AIR VENTS SINCE THEY

MUST ALWAYS BE OPEN FOR PROPER

MOTOR COOLING.

The key to efficient operating is controlling the pressure

and surface contact between the disc and work piece.

Flat surfaces are ground at an acute angle, usually 10 to

20 degrees with the work piece. Allow the disc to reach

full speed before starting to grind. Too great an angle

causes concentration of pressure on a small area which

may gouge or burn work surface.

LIVE TOOLINDICATOR

This tool features a live tool indicator (13) which

illuminates as soon as the tool is connected to the supply.

This warns the user that the tool is connected and will

operate when the switch is pressed.

MAINTENANCE

After use, check the tool to make sure that it is in good

condition. It is recommended that you take this tool to a

Ryobi Authorized Service Center for a through cleaning

and lubrication at least once a year.

English

F D E I P NL S DK N FIN GR H CZ RUS PL

SLO TR

EAG-8512R_20 lgs 6/10/05 14:58 Page 5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ryobi eag 8512 r Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info