Bedienungsanleitung Ryobi eid 500 re (Seite 11 von 83) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

388689

Zoom out

Zoom in

Vorherige Seite

1/83

Nächste Seite

OPERATING

NEVER COVER THE AIR VENTS (J) SINCE THEY MUST

ALWAYS BE OPEN FOR PROPER MOTOR COOLING.

DRILLING IN WOOD

To prevent ugly splits around the drill hole on the reverse

side of the workpiece, put a piece of scrap timber under

the work piece.

DRILLING IN METAL

Metals such as steel brass, aluminum sheets, stainless

steel, and pipe may also be drilled. Mark the point to be

drilled with a nail or punch.

Do not use impact mode on these materials.

DRILLING IN CONCRETE

Stone and masonry are generally drilled in the impact

drilling mode.

When drilling in delicate materials such as wall tiles,

it is essential to start with ordinary drilling and, once the

tile is pierced, to continue with impact drilling.

In deep bore holes the drill bit should be pulled out

occasionally in order to remove the debris from the

drill and hole.

AUXILIARY HANDLE AND STOPPER POLE

(FIG. 6)

Auxiliary handle

The auxiliary handle (H) can be rotated 360º.

Loosen the handle grip by turning in direction L,

and tighten it at an easy to-use position by turning

the grip in direction M.

Depth stopper

Holes of a fixed depth can be accurately bored by using

the depth stopper (G).

The depth of the hole will be the distance from the end

of the bit to the end of the stopper pole.

By turning the handle grip in direction L, the stopper pole

can be released and the depth adjusted. After adjusting

the depth, fix the stopper pole again by turning

the handle grip in direction M.

BIT STORAGE

(EID-750REN) (FIG. 7)

The auxiliary handle also contains a compartment to

store dill bits. To access this compartment unscrew

the end cap below the yellow trim on the handle in an

anticlockwise direction.

LIVE TOOLINDICATOR

This tool features a live tool indicator (K) which

illuminates as soon as the tool is connected to the

supply. This warns the user that the tool is connected

and will operate when the switch is pressed.

MAINTENANCE

After use, check the tool to make sure that it is in good

condition. It is recommended that you take this tool to

a RYOBI Authorized Service Center for a thorough

cleaning and lubrication at least once a year.

DO NOT MAKE ANY ADJUSTMENTS WHILE

THE MOTOR IS IN MOTION. ALWAYS DISCONNECT

THE POWER CORD FROM THE POWER SUPPLY

BEFORE CHANGING REMOVABLE OR CONSUMABLE

PARTS (BLADE, BIT, ETC.), LUBRICATING OR

WORKING ON THE UNIT.

WARNING

To ensure safety and reliability, all repairs should

be performed by an AUTHORIZED SERVICE

CENTER or other QUALIFIED SERVICE

ORGANIZATION.

SAVE THESE INSTRUCTIONS FOR FUTURE

REFERENCE.

English

F D E I P NL S DK N FIN GR H CZ RUS PL

SLO TR

EID-500RE&750REN_20 lgs 26/08/05 11:30 Page 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ryobi eid 500 re Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info