SAFETYINSTRUCTIONS
■ Noise level. Noise level (or sound pressure level) in
the work area can exceed 85 dB(A). In this case,
operators should take appropriate measures to
ensure sound insulation and wear ear protectors.
Important
To protect yourself from the risk of electric shock,
injury and fire when using an electric tool, it is
imperative to take the following basic safety
precautions. Before you use your tool, read
these instructions carefully and make sure that
you understand them thoroughly.
■ Make sure that the supply voltage (Volts) used
corresponds to the voltage marked on the tool's rating
plate.
■ When using cable drums, run all the cable off the
drum. Minimum cable across section: 1.0 mm.
■ When using the electric hammer drill outdoors,
connect it to an outdoor-grade extension cable type
H07RN-F 2G, 1.0 mm and rain-water-protected plugs
in proper working order.
■ Make sure of your footing when drilling freehand.
■ Before drilling,use a line detector to locate concealed
electric, water or gas lines in walls. Avoid touching
live components or conductors.
■ Wear goggles and use a dust mask on jobs
generating dust.
■ Do not use your hammer drill near flammable liquids
or gases.
■ Always pull the plug out of the socket before cleaning
your tool or changing accessories.
■ Keep the power cable in good condition. Oil and acid
can damage the cable.
■ Never overload the tool.
■ Make sure your workplace is safe.
Important
It is imperative to follow all national safety
regulations concerning installation, operation and
maintenance of the tool.
■ If incorrectly fitted, chisel bits and drill bits may be
flung out of the tool accidentally and cause serious
injury. Before you start using your hammer drill,
always check that the chisel or drill bit is properly
locked in the chuck.
■ Examine the chuck regularly for signs of wear or
damage.
■ Always press the hammer drill against the work
surface (wall, ceiling, etc.) before you start it.
■ When you are finished, unplug the hammer drill from
the power supply and remove the chisel or drill bit.
■ Always disconnect the hammer drill from the power
supply before you change the chisel or drill bit.
■ Wear safety goggles to protect your eyes from flying
particles and splinters. Have other workers do the
same. Wear a helmet and put up partition walls in
your work place!
■ Wear work gloves to protect fingers from bruising and
grazing.
■ Vibrations can injure the hand-arm system. Keep
exposure to vibrations as short as possible.
■ Always keep the power cord behind the tool.
■ Store the tool out of the reach of children.
■ When using the tool, always hold it with both hands
and ensure that you have stable footing.
■ Chisels may only be used with ERH-750V with
Rotostop engaged.
■ Chisels may not be used with the ERH-650V, as this
model does not have Rotostop feature.
7
GB
English
F D E I P NL S DK N FIN GR H CZ RUS PL
RO
SLO TR
HR
PRODUCT SPECIFICATIONS
ERH-650V ERH-650V ERH-750V ERH-750V
Voltage 230V 50 Hz 110V 50 Hz 230V 50 Hz 110V 50 Hz
AC only AC only AC only AC only
Power consumption 650W 650W 710W 650W
No Load speed 0 - 1100 min
-1
0 - 1100 min
-1
0 - 1100 min
-1
0 - 1100 min
-1
Maximum drilling capacity:
- steel 13 mm 13 mm 13 mm 13 mm
- concrete / stone 20 mm 20 mm 24 mm 24 mm
Tool attachment SDS-plus SDS-plus SDS-plus SDS-plus
Weight 3.20 kg 3.20 kg 3.20 kg 3.20 kg
