Bedienungsanleitung Ryobi ess 2590 v (Seite 14 von 121) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

390130

Zoom out

Zoom in

Vorherige Seite

1/121

Nächste Seite

OPERATION

PAPER PUNCH (Fig. 6)

A paper punch template has been supplied with your

sander for aligning and punching holes in sandpaper.

The punched holes must align with the holes in the

sander cushion.

■ Install sandpaper on your sander.

■ Align sander cushion over the paper punch.

■ Push down on sander

SANDPAPER SELECTION

Selecting the correct size grit and type sandpaper is an

extremely important step in achieving a high quality

sanded finish. Aluminum oxide, silicon carbide, and other

synthetic abrasives are best for power sanding. Natural

abrasives, such as flint and garnet are too soft for

economical use in power sanding.

In general, coarse grit will remove the most material and

finer grit will produce the best finish in all sanding

operations. The condition of the surface to be sanded will

determine which grit will do the job. If the surface is

rough, start with a coarse grit and sand until the surface

is uniform. Medium grit may then be used to remove

scratches left by the coarser grit and finer grit used for

finishing of the surface. Always continue sanding with

each grit until surface is uniform.

Note: DO NOT use sander without sandpaper. Doing so

will damage the cushion.

PREPARING FOR OPERATION

CAUTION

Be careful not to let your hand completely cover

air vents.

SANDING (Fig. 1)

WARNING

Unsecured work could be thrown towards the

operator causing injury.

Hold your sander in front and away from you, keeping it

clear of the workpiece. Start your sander by pressing the

switch button to "ON" position and letting the motor build

to its maximum speed. Gradually lower your sander on

the work with a slight forward movement. Move it slowly

using forward and backward strokes.

DO NOT FORCE. The weight of the unit supplies adequate

pressure, so let the sandpaper and sander do the work.

Applying additional pressure only slows the motor, rapidly

wears sandpaper and greatly reduces sander speed.

Excessive pressure will overload the motor causing

possible damage from motor overheating and can result in

inferior work.

Any finish or resin on wood may soften from the frictional

heat. Do not allow sanding on one spot too long as the

sander's rapid action may remove too much material,

making the surface uneven.

WARNING

Do not wear loose clothing or jewelry when

operating sander. They could get caught in

moving parts causing serious injury. Keep head

away from sander and sanding area. Hair could

be drawn into sander causing serious injury.

ORBITAL MOTION (Fig. 2)

Orbital motion is ideal for fast cutting action when removing

old finishes, smoothing rough wood, cutting stock down to

required dimensions, or for finishing surfaces to be painted.

The sandpaper moves in tiny circles at a very high speed,

allowing the sander to move easily.

WARNING

Collected sanding dust from sanding surface

coatings such as polyurethanes, linseed oil, etc.

can self-ignite in your sander dust bag or

elsewhere and cause fire. To reduce the risk of fire

always empty your dust bag frequently while

sanding and never store or leave a sander without

totally emptying its dust bag. Also follow the

recommendations of the coatings manufacturers.

USING THE DUST BAG ASSEMBLY

The dust bag assembly provides a dust collection system

for the sander. Sanding dust is drawn up through the

holes of the sanding disc and collected in the dust bag

during sanding.

TO ATTACH THE DUST BAG ASSEMBLY (Fig. 3)

Follow these directions to attach the dust bag assembly.

■ Unplug the sander.

WARNING

Failure to unplug the tool could result in

accidental starting causing possible serious injury.

■ Slide the dust bag assembly onto the blower exhaust

on the sander using a slight twisting motion.

English

F D E I P NL S DK N FIN GR H CZ RUS PL

SLO TR

ESS-1890ESS-2590V(EU)-25.qxd 8/15/04 4:52 PM Page 10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ryobi ess 2590 v Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info