Bedienungsanleitung Ryobi LSDT1202 (Seite 7 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

513654

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

English

FR DE ES IT NL PT DK SE FI NO RU PL CZ HU RO LV LT EE HR SI SK GR TR

INSTALLING BITS

See Figure 6 - 7.

 Lock the switch trigger by placing the direction of

rotation selector in the center position.

 Open or close the chuck jaws to a point where the

opening is slightly larger than the bit size you intend to

use. Also, raise the front of the drill slightly to keep the

bit from falling out of the chuck jaws.

 Insert the drill bit.

WARNING

Make sure to insert the drill bit straight into the chuck jaws.

Do not insert the drill bit into the chuck jaws at an angle

then tighten. This could cause the drill bit to be thrown

from the drill, resulting in possible serious personal injury

or damage to the chuck.

 Tighten the chuck jaws on the drill bit.

NOTE: Rotate the chuck body in the direction of the arrow

marked LOCK to close the chuck jaws. Do not use a

wrench to tighten or loosen the chuck jaws.

REMOVING BITS

See Figure 6.

 Lock the switch trigger by placing the direction of

rotation selector in the center position.

 Open the chuck jaws.

NOTE: Rotate the chuck body in the direction of the arrow

marked UNLOCK to open the chuck jaws. Do not use a

wrench to tighten or loosen the chuck jaws.

 Remove the drill bit.

TWO-SPEED GEAR SWITCH (HIGH-LOW)

See Figure 9.

A slide switch is located on top of the drill to select either

low (1) or high (2) speed. When using drill in the low (1)

speed range, speed will decrease and unit will have more

power and torque. When using drill in the high (2) speed

range, speed will increase and unit will have less power

and torque. Use low (1) speed for high power and torque

applications and high (2) speed for fast drilling or driving

applications.

ADJUSTABLE TORQUE CLUTCH

See Figure 8.

When using the drill-driver for various driving applications,

it becomes necessary to increase or decrease the torque

in order to help prevent the possibility of damaging screw

heads, threads, workpiece, and so on. In general, torque

intensity should correspond to the screw diameter. If the

torque is too high or the screws too small, the screws may

be damaged or broken.

The torque is adjusted by rotating the torque adjustment

ring. The torque is greater when the torque adjustment

ring is set on a higher setting. The torque is less when the

torque adjustment ring is set on a lower setting.

The proper setting depends on the type of material and the

size of screw you are using.

ADJUSTING TORQUE

 Identify the 24 torque indicator settings located on the

front of the drill.

 Rotate adjusting ring to the desired setting.

1 - 4 For driving small screws

5 - 8 For driving screws into soft material

9 - 12 For driving screws into soft and hard

materials

13 - 16 For driving screws in hard wood

17 - 20 For driving large screws

21 -

For drilling

DRILLING

 Check the direction of rotation selector for the correct

setting (forward or reverse).

 Secure the material to be drilled in a vise or with

clamps to keep it from turning as the drill bit rotates.

 Hold the drill firmly and place the bit at the point to

be drilled.

 Depress the switch trigger to start the drill.

 Move the drill bit into the workpiece, applying only

enough pressure to keep the bit cutting. Do not force

the drill or apply side pressure to elongate a hole. Let

the tool do the work.

WARNING

Be prepared for binding at bit breakthrough. When these

situations occur, drill has a tendency to grab and kick

opposite to the direction of rotation and could cause loss

of control when breaking through material. If not prepared,

this loss of control can result in possible serious injury.

 When drilling hard, smooth surfaces, use a center

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ryobi LSDT1202 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info