Bedienungsanleitung Ryobi PPW-3000 (Seite 26 von 309) (Alle Sprachen)

557213

Zoom out

Zoom in

Vorherige Seite

1/309

Nächste Seite

OPERATION

NOTE: If the engine is cold, close the choke fully. If

the engine is warm, open the choke lever half-way or

keep it opened fully.

■ Give the start recoil short, brisk pulls to start the

engine.

■ If the engine fires, or begins to sputter and/or cough

without catching, move the choke lever to the half-

way position.

NOTE: Never pull the recoil starter more than four or

five times with the choke closed as this causes

flooding.

■ With the choke in the half-way position, pull the recoil

starter again. The engine should now start.

NOTE:If the choke remains in the closed position, the

engine will continue to sputter and/or cough but will

not start.

■ As the engine warms up, move the choke lever slowly

to position B (OPEN) (38).

■ Return the recoil starter gently to the engine housing.

Do not allow the rope to snap back.

■ Let the engine warm up a few minutes before using.

To stop the engine using the ON/OFF switch:

■ Turn the ON/OFF switch to off ( O ) (37).

■ Close the fuel valve.

To stop the engine using the fuel valve:

■ Close the fuel valve and wait for the engine to stop.

NOTE: Avoid letting fuel remain in the carburetor for

long periods as this can clog carburetor passages

with impurities resulting in malfunctions.

SELECTing the RIGHT QUICK-CONNECT NOZZLE

FOR THE JOB

( Figure 12 - 13.)

The nozzle colors and spray patterns are:

• black (low pressure),

• white (medium pressure) 40˚,

• green (medium pressure) 25˚,

• yellow (high pressure) 15˚,

• red (high pressure) 0˚.

NOTE: For a gentle rinse, select the white 40˚ or

green 25˚ nozzle. Scouring the surface requires a

more direct spray of water. Select the yellow 15˚ or

red 0˚ nozzle for tough jobs.

CAUTION:

NEVER change nozzles without locking the lock

out (40) on the spray wand.

Using the quick-connect collar, changing nozzles to easy.

■ Turn off the pressure washer and shut off the water

supply. Pull trigger to release water pressure.

To connect a nozzle to the spray wand:

■ Engage the lock on the wand (39) by pushing up on

the lock out (40) until it clicks into the slot.

■ Pull back and hold the collar (41).

■ Insert the desired nozzle then release the collar. Tug

on the nozzle to be certain it is secured properly.

■ Release the lock out on the wand by pushing it down

into its original position.

To disconnect a nozzle from the spray wand once the

cleaning job is complete:

■ Engage the lock out on the wand by pushing up on

the lock out until it clicks into the slot.

■ Pull back and hold the collar then remove the nozzle

by pulling if from the collar. Place nozzle in the nozzle

storage area on the top of the machine.

USING THE SPRAY WAND TRIGGER

( Fig 14.)

To engage the lock out:

■ Push up on the lock out until it clicks into the slot.

To disengage the lock out:

■ Push the lock out down and into its original position.

MOVING THE PRESSURE WASHER

(Fig.15)

■ Loosen the pivot knob located halfway down the

spray wand storage pipe.

■ Grasp the handle at the rear of the pressure washer.

Turn the top section of the pressure washer until it is

fully extended. Retighten the pivot knob.

■ Grasp the moving handle and lift the machine off the

resting foot. Roll the machine to the desired position.

STORING THE PRESSURE WASHER

(Fig.16)

Allow 30 minutes of “cool down” time before placing the

storage handle in the “store” position. Store machine in a

dry, covered area where the weather can’t damage it.

WASHING WITH DETERGENT

(Fig.17)

Use only soaps designed for pressure washers;

household detergents can damage the pump. Many

detergents require mixing prior to use. Follow

manufacturer’s instructions on the solution bottle.

Prepare cleaning solution as instructed on the solution

bottle.

■ Place the injection hose (26) in the bottom of the

detergent bucket (2).

■ Carefully pour the cleaning solution into the bucket

taking care not to splash the solution.

■ Install the black nozzle on the spray wand.

■ Spray the detergent on a dry surface using long,

even, overlapping strokes. To prevent streaking, do

not allow the detergent to dry on the surface.

Before shutting off the engine:

■ Place the injection hose in a bucket of clean water.

English

F D E I P NL S DK N FIN GR HU CZ RU RO PL SLO HR TR EST LT LV SK BG

PPW-3000_25lgs.qxd 3/26/01 11:52 PM Page 18

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ryobi PPW-3000 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info