Bedienungsanleitung Ryobi RPW3200Y (Seite 11 von 44) (Englisch)

733430

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

■ Make sure the air filter is clean.

■ Check both the engine lubricant level and

the fuel tank level. Refill as needed.

■ Inspect the work area for hazards.

■ If there is excessive noise or vibration, stop

the product immediately.

NOZZLE MAINTENANCE

Excessive pump pressure (a pulsing sensation

felt while squeezing the trigger) may be the

result of a clogged or dirty nozzle.

■ Turn off the high pressure cleaner and shut

off the water supply. Squeeze trigger to

release water pressure.

■ Remove the nozzle from the spray wand.

NOTE: Never point the spray wand to

yourself and others.

■ Using a straightened paper clip or nozzle

cleaning tool (not provided), free any

foreign materials clogging or restricting the

nozzle.

■ Using a garden hose, flush debris out of the

nozzle by back flushing (running the water

through the nozzle backwards or from the

outside to the inside).

■ Reconnect the nozzle to the spray wand.

■ Turn on the water supply and start the

engine.

CLEANING THE AIR FILTER

See pages 33-34.

A dirty air lter will cause starting difculty,

loss of performance, and shorten the life span

of the engine. Check the air lter monthly. For

best performance, replace the air lter at least

once a year.

REPLACING THE SPARK PLUG

See page 35.

■ Clean the area around the base of the

spark plug before removing to keep dirt

and debris out of the engine. Remove

spark plug.

■ Clean the carbon deposits on the spark

plug electrode using a plug cleaner or wire

brush. Replace the plug if worn. To replace

the spark plug, see page 34. Use spark

plug model BPR7HS (NGK) or equivalent.

■ Check electrode gap. The gap should be

0.7- 0.8 mm (0.03 in.). Adjust the gap, if

necessary, by carefully bending the ground

electrode.

■ Reinstall spark plug and tighten securely.

CHANGING THE ENGINE LUBRICANT

See page 36.

NOTE: Drain the lubricant while the engine

is still warm but not hot. Warm lubricant will

drain quickly and more completely.

NOTE: Consult hazardous waste management

guidelines in your area for the proper way of

used lubricant disposal.

PUMP LUBRICATION

The pump used in the high pressure cleaner

was lubricated with a sufcient amount of high

grade lubricant for the life of the product under

normal operating conditions. Therefore, no

further lubrication is required.

SYMBOLS ON THE PRODUCT

Safety alert

Read and understand

all instructions before

operating the product, follow

all warnings and safety

instructions.

Wear full eye and ear

protection.

To reduce the risk of injury

from kickback, hold the spray

wand securely with both

hands when the product is on.

Never point the spray wand to

people, animals, the machine

body, power supply, or any

electric appliances.

The product is not suitable

for connection to the drinking

water mains.

Burst hazard

To reduce the risk of injury

from high-pressure injection,

do not direct spray at people

or animals.

Failure to use in dry conditions

and to observe safe practices

can result in electric shock.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ryobi RPW3200Y Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info