Bedienungsanleitung Ryobi RY18PSX10A (Seite 5 von 240) (Alle Sprachen)

798982

Zoom out

Zoom in

Vorherige Seite

1/240

Nächste Seite

ENGLISH

Original Instructions

Tip contact in some cases may cause a sudden reverse

reaction, kicking the guide bar up and back towards the

operator.

Pinching the saw chain along the top of the guide bar may

push the guide bar rapidly back towards the operator.

Either of these reactions may cause you to lose control of

the saw which could result in serious personal injury. Do not

rely exclusively upon the safety devices built into your saw.

As a pruning saw user, you should take several steps to

keep your cutting jobs free from accident or injury.

Kickback is the result of pruning saw misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below:

■Maintain a firm grip, with thumb and fingers

encircling the pruning saw rear handle, with both

hands on the saw and position your body and arm to

allow you to resist kickback forces. Kickback forces

can be controlled by the operator, if proper precautions

are taken. Do not let go of the pruning saw.

■Do not overreach and do not cut above shoulder height.

This helps prevent unintended tip contact and enables

better control of the pruning saw in unexpected situations.

■Only use replacement guide bars and saw chains

specified by the manufacturer. Incorrect replacement

guide bars and saw chains may cause chain breakage

and/or kickback.

■Follow the manufacturer’s sharpening and maintenance

instructions for the saw chain. Decreasing the depth

gauge height can lead to increased kickback.

ADDITIONAL SAFETY WARNINGS

■Attend a professionally organised course on the use and

maintenance of pruning saws, preventative actions, and

first aid. Keep these instructions safe for later use.

■Pruning saws are potentially dangerous tools. Accidents

involving the use of pruning saws often result in loss

of limbs or death. Falling branches, toppling trees,

rolling logs can all kill. Diseased or rotting timber poses

additional hazards. Assess your capability of completing

the task safely. If there is any doubt, leave it to a

professional tree surgeon.

■Do not cut vines or small undergrowth (less than 30 mm

in diameter).

■It is recommended to practise cutting logs on a saw-

horse or cradle when operating the product for the first

time.

■The size of the work area depends on the job being

performed and the size of the tree or workpiece involved.

The operator needs to be aware and in control of

everything happening in the work area.

■Do not use a back-and-forward sawing motion. Let the

chain do the work. Keep the chain sharp, and do not try

to push the chain through the cut.

■Do not put pressure on the saw at the end of the cut.

Be ready to take on the weight of the saw as it cuts free

from the wood. Failure to do so could result in possible

serious personal injury.

■Do not stop the saw in the middle of a cutting operation.

Keep the saw running until it is already removed from

the cut.

■To reduce the risk of injury associated with contacting

moving parts, always turn off the product, remove the

battery pack, and make sure that all moving parts have

come to a complete stop:

●before cleaning or clearing a blockage

●before leaving the product unattended

●before installing or removing attachments

●before checking, conducting maintenance, or

working on the product

■Injuries may be caused, or aggravated, by prolonged use

of the product. When using the product for prolonged

periods, ensure to take regular breaks.

■If the product is dropped, suffers heavy impact, or begins

to vibrate abnormally, immediately stop the product and

inspect for damage or identify the cause of the vibration.

Any damage should be properly repaired or replaced by

an authorised service centre.

■Operate the product only in temperatures between 0°C

and 40°C.

■Store the product in a location where the ambient

temperature is between -10°C and 50°C.

PERSONAL PROTECTIVE EQUIPMENT

Good quality personal protective equipment, as used by

professionals, helps reduce the risk of injury to the operator.

The following items should be used when operating the

product:

■Safety helmet

–should comply with EN 397 and be CE marked

■Hearing protection

–should comply with EN 352-1 and be CE marked

■Eye and face protection

–should be CE marked and comply with EN 166 (for

safety glasses) or EN 1731 (for mesh visors)

■Gloves

–should comply with EN ISO 11393-4 and be CE

marked

■Leg protection (chaps)

–should comply with EN ISO 11393-2, be CE marked

and provide all-round protection

■Pruning saw safety boots

–should comply with EN ISO 20345:2004 and be

marked with a shield depicting a pruning saw to

show compliance with EN ISO 11393-3. (Occasional

users may use steel toe-cap safety boots with

protective gaiters, which conform to EN ISO 11393-5

if the ground is even and there is little risk of tripping

or catching on undergrowth).

■Pruning saw jackets for upper body protection

–should comply with EN ISO 11393-6 and be CE

marked

ADDITIONAL BATTERY SAFETY WARNINGS

■To reduce the risk of fire, personal injury, and product

damage due to short circuit, never immerse the tool,

battery pack, or charger in fluid or allow fluid to flow

inside them. Corrosive or conductive fluids, such as

seawater, certain industrial chemicals, and bleach or

bleach-containing products, etc., can cause a short

circuit.

Ryobi RY18PSX10A Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info