Bedienungsanleitung SAB NVR2000A (Seite 1 von 2) (Englisch)

670257

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

54 6 7

1 2 3

Quick Installation Guide

Network Video Recorder

Model: SAB2000A

V1.0

WARNING

Before installing a hard disk drive (HDD), please make sure the power

is disconnected from the NVR.

Find the

antistatic gloves from the package of the NVR and wear the

gloves.

It is recommended that a hard drive be used in 7200 high-speed or

above.

Power cable

HDD

Data cable

It is recommended to use SATA type of hard disk for recording.

Note

1. Remove the cover from the NVR by unfastening the screws on the

rear and side.

2. Connect one end of the data cable and power cable to the

motherboard of NVR and the other end to the HDD.

3. Place the HDD on the bottom of the device and then fasten the

screws on the bottom to x the HDD.

4. Re-install the cover of the NVR and fasten screws.

Internet users

IP Camera

Power Switch

Power Supply

HDMI Video Output

VGA Video Output

USB Interfaces

DC 12V

POWER

HDMI

VGA

LAN

USB

ALARM N1

1 2 3 4

Alarm IN Alarm OUT

Router

Internet users

Procedure

1. Connect your display to one of the video outputs (VGA or HMDI

interface).

2. Connect an external storage device to the USB interface of the NVR as

a backup.

3. Connect a mouse to the USB interface.

4. Connect an alarm input device and an alarm output device to the

alarm input interface and alarm output interface respectively.

5. Some devices need to connect to your router using an Ethernet cable,

including the NVR, PC, IP Camera.

6. Connect the power adapter to the power input port.

NVR

USB Mouse

DC Power Adapter

Screw Pack

Antistatic Gloves

Data Wire and Power Wire of the Hard Drives

Quick Installation Guide

Ethernet Cable

1. Turn on the power switch on the rear panel.

After the NVR starts up successfully, the Power LED and HDD LED

indicators will turn green. The startup page is displayed on the screen.

2. Login page.

Select the Language, Enter the Username and Password, then click

on the Login button.

Default username is

admin with no password

Package Contents

1 Before You Start

2 Hard Disk Installation

3. For the initial log in, the system will prompt you to change your

password. Once done, click the OK button.

4. After modifying the password, you will be taken to the Setup

Wizard.

1. Setting the time. If you don’t want to use the Setup Wizard next

time, uncheck the Setup Wizard checkbox. Click the Next button.

2. Select the HDD you would like to use, then click the Format Hard

Disk button to set up the HDD. Note that this will delete all les on

the HDD.

Select a protocol depending on which IP Camera you have.

H.264 protocol: The High Denition(HD) IP Cameras for private.

ONVIF protocol: IP Cameras which support ONVIF protocol.

3. You can add an IP Camera that is connected to the internet on the

NVR.

You can congure the following information for your IP Camera.

The Setup Wizard can walk you through some important settings on

the NVR.

Input a new password,

then click OK.

1. Select Your IP Camera

2. Click Add

3 Device Connection

4 Log In 5 Setup Wizard

Uncheck the checkbox

2. Click Format Hard Disk

3. Click Next

1. Select your HDD

Format Hard Disk

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

SAB NVR2000A Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von SAB NVR2000A

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info