8
Pos: 19.2 /Inne
14 MOWING
Pos: 19.3 /Inne12
Safety instruction!
See table for explanation of symbols
page 3
Pos: 19.4 /Inne
Mowing on slopes
Pos: 19.5 /Inne
NOTE
The mower can be used on banks and slopes with a gr
angle).
For safety reasons, however, we urgently recommend you
theoretical performance potential. Always make sure you have a fir
Manually guided lawnmowers should never
excess of 26% (15° angle of slope). Stability may be lost
Pos: 19.6 /Inne
Handling the cable during use
Pos: 19.7 /Inne
Prepare the cable in such a way that the machine can pull it behind easily over the lawn
area already mown. When the mower is turned, the cable relief automatically places the
cable on the other side of the handle bar.
Make sure that the cable is kept away from the cutti
loops.
Examine the mains connection cable before any mowing f
use it if it is in perfect condition.
Pos: 19.8 /Inne
Checking operating saf
Pos: 19.9 /Inne40
The lawnmower is equipped with a motor stop device.
Before every mowing job, make sure that the motor stop safety cont
perfectly. When the control bar is released, the motor and cutter bar must come to a
standstill within three seconds.
After release, the bar must always return to the position shown in the "component
description" diagram.
If this is not the case, it must be checked immediately by an aut
Risk of inju
If the blade run-on time is longer, stop using the equipment and take it to an authorised
workshop.
Measuring run-on time
After the electric motor has been started, the blade rotates and a wind-like noise can be
heard.
The run-on time corresponds to the duration of the wind-like noise after the electric
motor has been switched off, it can be measured using a stopwatch.
Machine safety and protective devices must not be manipulated or disabled.
Make sure that all protective devices have been attached properly and are not
damaged.
Check the upper part of the bar (insulation) for damage.
damaged, contact the nearest authorised workshop wit
injuries (electric shock) can occur through touching the live parts.
To avoid risk, check the condition and firm attachment of the blade before every
mowing job. The blade attachment screw must always be ti
workshop since an insulation protection talways has to be carried out after repairs
and maintenance work on insulation parts (e.g. blade screw) in accordance with the
applicable standard DIN EN 60335. A worn or damaged blade must always be
replaced. (refer here to the chapter "Cutter blade care")
In addition, check the fan, blade coupling and fan housing eve
wear and a tight fit. Also check equipment screws and nuts for a f
necessary.
If the mower mechanism becomes blocked e.g. by colliding with an obstacle, have an
authorised workshop check whether any parts of
Always have any necessary repairs done by an authorised workshop t
If the machine starts to vibrate unusually heavily or to make unusual noises, please
have it checked immediately by an authorised workshop.
Pos: 19.10 /
Time restrictions
Pos: 19.11 /
The time at which lawnmowers may be used varies from region to region. Please ask
the corresponding authorities before using your mower.
Pos: 19.12 /In
Tips on caring for your lawn (Illu
Pos: 19.13 /In
WARNING
Remove any objects (stones, wood, branches, etc.) from the l
cut; but still watch out for objects lying around during the mowing process.
Ask your dealer about lawn care instructions. Informat
mowing can also be found on the manufacturer website.
Pos: 20.1 /----
Pos: 20.2 /Inne
15 SERVICE INTERVALS
Pos: 20.3 /Inne
IMPORTANT
Avoid damage! Under extreme or unusual condi
than the ones specified below may be necessary. If you establish any probl
please contact an authorised workshop.
Pos: 20.4 /Inne
Carry out routine servicing on the machine in line with the following servicing intervals.
Work must be carried out at the following servicing intervals in addition to the
maintenance work listed in these operating instructions.
Pos: 20.5 /Inne
Before initial
• Check all screw connections for a tight fit.
• Check the cutting blade screw and have an authorised worksh
necessary.
• Check whether the safety control bar for the engine brake is working perfectly.
• Check that all protective devices have been attached properly and are not
damaged.
Pos: 20.6 /Inne
Before every operation
• Check the lawn area and remove any objects.
• Check the area of the boundary wires (if an automatic mower is being used for
lawn care).
• Check the condition and firm fit of the blade, if necessary have an aut
workshop tighten the blade screw.
• Check whether the safety control bar for the engine brake is working perfectly.
• Check that all protective devices have been attached properly and are not
damaged.
• Check grass collecting equipment for wear or loss of functionality.
• Check the upper part of the bar (insulation) for damage.
• Check the connection cable for damage and ageing.
Pos: 20.7 /Inne
Every 10 operating hours
• Check all screw connections for a tight fit.
• Check the fan, blade coupling and fan housing regularly for wear and a tight fit.
Pos: 20.8 /Inne
After every operation
• Clean the mower.
• Check the blade for damage and wear.
Pos: 20.9 /Inne3458180_15
Every 15-20 operating hours or annual
• Lubricate the wheel bearings.
Pos: 21.1 /----
Pos: 21.2 /Inne 1
16 CARE AND SERVICING OF Y
Pos: 21.3 /Inne748 @ @ 1
Regular care is the best way to guarantee a long service life and problem-free
operation. Insufficient equipment maintenance will lead to
Pos: 21.4 /Inne
Only use original spare paronly those guarantee safety and quality!
Pos: 21.5 /Inne749_1521.
Safety instruction!
See table for explanation of symbols
page 3
Pos: 21.6 /Inne
Cleaning (Illustration O )
Pos: 21.7 /Inne
Remove dirt and grass residue immediately after finishing mowing. Place the mower on
its side and use a brush or cloth to clean.
ATTENTION
Do not put your fingers into t
fan. If the blade bar is rotated during cleaning, there is a risk that your finger
may become caught between the fan and the fan housi
IMPORTANT
Never spray the mower with water. This may damage the electrical systems.
Pos: 21.8 /Inne
