661079

Sabo 54-K VARIO B Seite 41

41
Zoom out
Zoom in
Vorherige Seite
1/100
Nächste Seite
7
Raise the handlebar (Illustration A1 + B1 + V4 )
Pos: 15.6 /Innenteil/Vorbereitende Arbeiten/Bowdenzüge nicht knicken oder einklemmen WICHTIG @ 44\mod_1469603773573_1521.docx @ 508855 @ @ 1
IMPORTANT
Make sure the throttle cables are not kinked or jammed when lifting the
handlebars.
Pos: 15.7 /Innenteil/Vorbereitende Arbeiten/Führungsholm hochstellen Text 47/54er Redesign BBC, Schnellspanner @ 43\mod_1464782315925_1521.docx @ 497998 @ @ 1
Pull the handlebar which is collapsed in a Z-shape upwards into place in the following
sequence:
– First lift the bottom part of the handlebar A1 , push the ends of this bottom part as
far apart as necessary for the locking cams facing the inside to lock into the
respective bore holes B1 .
Three different handlebar heights can be set.
– Tighten the wing nuts on both sides by hand B1 .
– Lift the top part of the handlebar until the top part and the bottom part of the
handlebar are on the same level V4 .
– The quick releases for attachment of the top part and the bottom part of the
handlebar are preset by the manufacturer.
1. Pull the quick releases upwards to the handlebar.
2. Tighten the screws hand-tight.
3. Open the quick releases.
4. Tighten the screws by a quarter to a half of a turn.
5. Pull the quick releases up again and check whether the bars are tightly
connected, correct again if necessary.
– Keep this setting. If the tension slacks over time, the screws have to be tightened
again.
Pos: 15.8 /Innenteil/Beschreibung der Bauteile/47-K VARIO B, R47KB @ 37\mod_1435576626382_0.docx @ 397470 @ @ 1
47-K VARIO B, R47KB
Pos: 15.9 /Innenteil/Vorbereitende Arb eiten/Holmhöhenverstellung...Umschlagen des Holms Hinweis 43er Redesign @ 14\mod_1281595096269_1521.docx @ 111920 @ @ 1
CAUTION
When you activate the bar height adjustment, when loosening the wing nuts
B1 used to secure the bar bottom to the housing (only loosen sufficiently to
ensure that the bar can be moved freely) and snapping the locking cams out of
the drilled holes in the housing, it is possible that unintentional upsetting of the
bar may occur. In addition, this may result in crushed areas between the bar
bottom and the housing. This may result in a risk of injury!
Pos: 15.10 /Innenteil/Beschreibung der Bauteile/54-K VARIO B, JX90 @ 37\mod_1435576641609_0.docx @ 397498 @ @ 1
54-K VARIO B, JX90
Pos: 15.11 /Innenteil/Vorbereitende Arbeiten/Holmhöhenverstellung...Umschlagen des Holms Hinweis 54er Consumer @ 13\mod_1280323220198_1521.docx @ 110498 @ @ 1
CAUTION
When you activate the bar height adjustment, when loosening the grip nuts
B1 used to secure the bar bottom to the housing (only loosen sufficiently to
ensure that the bar can be moved freely) and snapping the locking cams out of
the drilled holes on the connecting bar, it is possible that unintentional upsetting
of the bar may occur. In addition, this may result in crushed points between the
bar bottom and the bar connection/housing. This may result in a risk of injury!
Pos: 15.12 /Innenteil/Beschreibung der Bauteile/Alle Modelle_dl_text_bold_8 @ 33\mod_1409212920947_1521.docx @ 245827 @ @ 1
All models
Pos: 15.13 /Innenteil/Vorbereitende Arbeiten/1.1 Holmstart-Montage (Abbildung L1 ) @ 0\mod_1127986352485_1521.docx @ 1681 @ 2 @ 1
Handle starter assembly (Illustration L1 )
Pos: 15.14 /Innenteil/Vorbereitende Arbeiten/Montage Starterseilhalter Text Messerbremse Subaru+Kawasaki @ 37\mod_1436189609320_1521.docx @ 399484 @ @ 1
– Remove the starter cable holder (1) from the tool bag.
– Unscrew the nut until the two halves can be pushed over the bar.
– There is a sticker (2) on the top bar showing the position of the starter cable
holder.
NOTE
For reasons of safety, the starter cable holder may only be fitted in the
prescribed position.
– Push the actuation lever (3) to the "STOP" position (4), pull the starter cable (5) out
and insert it into the starter cable holder.
– Fit the two halves (6) together, tighten the nut again. This prevents the starter
cable popping out.
The starter cable holder must be fitted / aligned in such a way that the starter cable
is freely accessible and does not rub against any other parts.
Pos: 15.15 /Innenteil/Vorbereitende Arbeiten/1.1 Grasfangsack am Mäher einhängen (Abbildung R1 + S1) @ 0\mod_1125644669425_1521.docx @ 1678 @ 2 @ 1
Attaching the grass collector to the mower (Illustration R1 + S1 )
Pos: 15.16 /Innenteil/Vorbereitende Arbeiten/Grasfangsack am Mäher einhängen Text 47er, 54er, SABO+JD @ 37\mod_1435645332635_1521.docx @ 397898 @ @ 1
– Insert the collecting bag frame into the grass catch with the bar first. Align the
upper seams of the grass catch to the bar.
Make sure that the protective corners of the grass catch cover the back corners of
the collecting bag frame (54-K VARIO B, JX90 only).
– Push the fixtures onto the front frame of the collecting bag frame R1 .
– Open the ejection flap of the mower upwards.
– Lift the grass collecting bag by the handle, insert the sloped channel (1) R1 on
the collecting bag opening into the ejector opening and hook the grass collecting
bag in place on the top of the mower housing using the two hooks at the side S1 .
– Close the ejector flap onto the grass collecting bag.
Pos: 15.17 /Innenteil/Vorbereitende Arbeiten/1.1 Schnitthöhe einstellen (Abbildung I ) @ 0\mod_1115201229609_1521.docx @ 1684 @ 2 @ 1
Adjusting the cutting height (Illustration I )
Pos: 15.18 /Innenteil/Sicherheitshinweise/Sicherheitshinweis: Messer, MotorStop @ 0\mod_1115201376187_1521.docx @ 1535 @ @ 1
Safety instruction!
See table for explanation of symbols page 3
Pos: 15.19 /Innenteil/Beschreibung der Bauteile/47-K VARIO B, R47KB @ 37\mod_1435576626382_0.docx @ 397470 @ @ 1
47-K VARIO B, R47KB
Pos: 15.20 /Innenteil/Vorbereitende Arbeiten/Schnitthöhe einstellen Text 47er, 43er @ 20\mod_1346321761447_1521.docx @ 154290 @ @ 1
You can set the desired cutting height with the adjustment lever (1) on the left of the
mower.
– Pull the lever out of the catch and latch again after a lateral move into the desired
position.
– The marking on the left of the housing indicates the cutting height.
Pos: 15.21 /Innenteil/Beschreibung der Bauteile/54-K VARIO B, JX90 @ 37\mod_1435576641609_0.docx @ 397498 @ @ 1
54-K VARIO B, JX90
Pos: 15.22 /Innenteil/Vorbereitende Arbeiten/Schnitthöhe einstellen Text 52er, 54er @ 0\mod_1127829117709_1521.docx @ 1700 @ @ 1
– The cutting height is set on the left hand side of the lawnmower
– Press the button with your thumb (1) and move the handle of the lawnmower into
the required position by moving it up or down (2).
– By letting go of the button, the lever locks into the required cutting height.
– The marking on the left of the housing indicates the cutting height.
Pos: 15.23 /Innenteil/Beschreibung der Bauteile/Alle Modelle_dl_text_bold_8 @ 33\mod_1409212920947_1521.docx @ 245827 @ @ 1
All models
Pos: 15.24 /Innenteil/Vorbereitende Arbeiten/Schnitthöhe einstellen Hinweis MUSTER @ 16\mod_1331722670371_1521.docx @ 134287 @ @ 1
IMPORTANT
Mowing at the lowest cutting height should only be carried out on level and plane
lawns!
Please note that the lower cutting height settings may only be used for optimum
conditions. If you select cutting height that is too low, the turf may be damaged
and under certain circumstances even destroyed.
Besides the cutting height, the driving speed also influences the cutting pattern
and collection result. Adapt the cutting height and driving speed to the grass
height to be cut, the motor drive may not need to be switched on.
Pos: 16.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_1521.docx @ 2070 @ @ 1
Pos: 16.2 /Innenteil/Vor der Ersten Inbetriebnahme/1 VOR DER ERSTEN INBETRIEBNAHME MÄHER @ 0\mod_1115210527828_1521.docx @ 1709 @ 1 @ 1
9 BEFORE USING THE LAWNMOWER FOR THE FIRST TIME
Pos: 16.3 /Innenteil/Sicherheitshinweise/Sicherheitshinweis: Stein @ 0\mod_1115200949078_1521.docx @ 1537 @ @ 1
Safety instruction!
See table for explanation of symbols page 3
Pos: 16.4 /Innenteil/Vor der Ersten Inbetriebnahme/Allgemeine Sicherheitshinweise Benzinmäher BBC + Text DLG @ 37\mod_1436248906019_1521.docx @ 400579 @ @ 1
Check all screw connections and the spark plug connector for a tight fit. Tighten the
screws if necessary. Attachment of the cutter bar must be checked in particular (refer
here to the chapter "Cutter bar care").
The blade attachment screw must always be tightened by an authorised workshop. If
the blade screw is too tight or too loose, the blade coupling and cutter bar can become
damaged or loose which can lead to serious injuries.
The lawn mower is equipped with a blade stop device.
Before using the equipment for the first time, make sure that the blade stop safety
control bar is working perfectly. When the control bar is released, the cutter bar must
come to a standstill within three seconds.
After release, the bar must always return to the position shown in the "component
description" diagram.
If this is not the case, it must be checked immediately by an authorised workshop.
Risk of injury!
If the blade run-on time is longer, stop using the equipment and take it to an authorised
workshop.
Measuring run-on time
After the mowing blade has been started, the blade rotates and a wind-like noise can be
heard.
The run-on time corresponds to the duration of the wind-like noise after the cutter bar
has stopped, it can be measured using a stopwatch.
Pos: 16.5 /Innenteil/Vor der Ersten Inbetriebnahme/Sicherheits- und Schutzeinrichtungen ... dürfen nicht manipuliert oder deaktiviert werden!_dl_text @ 38\mod_1437988093850_1521.docx @ 402470 @ @ 1
Machine safety and protective devices must not be manipulated or disabled!
Pos: 16.6 /Innenteil/Vor der Ersten Inbetriebnahme/Darauf achten ... Schutzeinrichtungen ordnungsgemäß angebracht und nicht beschädigt sind! @ 37\mod_1436249863921_1521.docx @ 400691 @ @ 1
Make sure that all protective devices have been attached properly and are not
damaged.
Pos: 16.7 /Innenteil/Vor der Ersten Inbetriebnahme/1.1 Öl einfüllen (Abbildung Y1 ) @ 0\mod_1115210961078_1521.docx @ 1711 @ 2 @ 1
… 41 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Sabo 54-K VARIO B wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info