Bedienungsanleitung Safety 1st OnBoard 35LT (Seite 21 von 32) (Englisch)

768795

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

35 36

Knowing Your Vehicle Belts

Review your vehicle owner’s manual for vehicle seat belt use with

child restraints. This is your best source for information concerning

your vehicle.

Not all vehicle belts will work with this child restraint. This child

restraint must be tightly locked in place at all times. You must

determine if your vehicle’s belts are compatible with this child

restraint.

Vehicle Belts • Automatic/Passive vehicle seat belts

You MUST have a lap belt to install any child

restraint. An automatic (passive) shoulder belt

may or may not have a separate lap belt.

• Do not use with inflatable seat belts

You may need to move the child restraint to another seating

location or use LATCH belts only.

• Vehicle belts in center of the door or side panel

You must move the child restraint to another seating location.

• Vehicle belts that are in front of the seat

bight

You may need to move the child restraint to

another seating location.

• ELR (Emergency Locking Retractor) vehicle belts

These belts only lock in a sudden stop or crash, and do not

properly secure a child restraint alone.

To determine if you have this type of belt,

gently pull the belt all the way out of the retractor

(spool), let it return several inches, then pull on

it again. If it moves freely, it is an ELR belt. If it is

locked and will not allow any more belt to come out, it is a

switchable retractor.

If you have an ELR lap and shoulder belt, review the “Vehicle Latch

Plate” section on page 36 to see if you need a locking clip.

WARNING: ELR lap-only belts MUST NOT be used with

this child restraint.

• Switchable Retractor

These belts switch from ELR to ALR (Automatic Locking Retractor).

You MUST have the vehicle belts in the locking mode to use them.

With a switchable retractor, pull the shoulder belt all the way out to

switch the retractor into the ALR mode before tightening.

Feed the slack back into the retractor while tightening.

• ALR (Automatic Locking Retractor)

These belts lock after pulling the webbing out and letting the belt

go back into the retractor an inch or two.

With an ALR belt, pull the belt all the way out before threading

through the child restraint.

Vehicle Latch Plates

• Check Latch Plates Grasp the tongue portion of the

latch plate (the part that goes

inside the buckle) and pull straight

out, in line with the lap belt.

If the latch plate does not slide

up and down the vehicle belt, you

have a locking latch plate. You

should not need to use a locking

clip.

Check your vehicle owner’s manual to determine the best way to

lock a child restraint in place and whether the latch plate or

retractor will accomplish this. If the latch plate slides up and down

on the belt, and you have an ELR retractor, you MUST use a lock-

ing clip to install the child restraint. See pages 51-52.

You may not need to use the locking clip with a switchable or ALR

retractor.

Locking Latch

Plate

Sliding Latch

Plate

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Safety 1st OnBoard 35LT Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info