Bedienungsanleitung Sage BJE520 - the Nutri Juicer Plus (Seite 6 von 34) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

714744

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

10 11

Care & Cleaning

Ensure the juicer is turned o by pressing the

ON / OFF button on the control panel to OFF.

Then switch the appliance o at the power

outlet and unplug the cord. Ensure the juicer

is correctly disassembled.

FOR EASIER CLEANING

• Clean as you go and avoid dried on juice or

pulp residue.

• Immediately after each use, rinse removable

parts in hot water to remove wet pulp. Allow parts

to air dry.

• To minimise cleaning, line the pulp container with

a plastic freezer bag to collect the pulp. Pulp can

then be used in other dishes or as compost for

the garden or discarded.

CLEANING THE MOTOR BASE

1. Wipe the motor base with a soft, damp cloth

then dry thoroughly.

2. Wipe any excess food particles from the

power cord.

Do not use abrasive scouring pads or cleaners

when cleaning the parts or motor base as they may

scratch the surface.

CLEANING THE FILTER BOWL

SURROUND, JUICER COVER,

FROOJIE

INSERT, FOOD PUSHER,

PULP CONTAINER

1. Wash all parts in warm soapy water with a soft

cloth. Rinse and dry thoroughly.

The lter bowl surround, juicer cover and pulp

container are dishwasher safe (top shelf only).

The Froojie

Insert is not dishwasher safe. Please

wash in warm water.

CLEANING THE JUICE JUG

1. Rinse the juice jug and lid with froth attachment

under running water.

2. Wash both parts in warm soapy water with

a soft cloth. Rinse and dry thoroughly.

• The juice jug and lid are dishwasher safe

(top shelf only).

• Discolouration of the plastic may occur

with strongly coloured fruit and vegetables. To

help prevent this, wash parts immediately after

use. If discolouration does occur, the plastic parts

can be soaked in water with 10% lemon juice or

they can be cleaned with a non abrasive cleaner.

WARNING

Do not immerse the motor base in water or

any other liquid. The centre of the juice disc

and feed chute contains small sharp blades

to process fruit and vegetables during the

juicing function. Do not touch blades when

handling the juice disc or feed chute.

CLEANING THE JUICE DISC

For consistent juicing results always ensure that

the juice disc is thoroughly cleaned using the

supplied cleaning brush.

1. Soak the juice disc in hot soapy water for

approximately 10 minutes immediately after

juicing is completed. If pulp is left to dry on

the lter it may clog the ne pores of the lter

mesh thereby lessening the eectiveness of

the juicer.

2. Using the cleaning brush, hold the juice disc

under running water and brush from the inside

of the basket to the outer rim. Avoid touching

the small sharp blades in the centre of the juice

disc. After cleaning the juice disc, hold it up

towards a light to ensure the ne mesh holes

are not blocked. If the holes are blocked, soak

the juice disc in hot water with 10% lemon juice

to loosen the blocked holes. Alternatively, wash

the juice disc in the dishwasher.

• The juice disc is dishwasher safe

(top shelf only).

• Do not soak the juice disc in bleach or other

abrasive cleansers.

• Always treat the juice disc with care as it can be

easily damaged.

Troubleshooting

POSSIBLE PROBLEM EASY SOLUTION

Machine will not work when

switched ON

•

The safety locking arm may not be correctly engaged in the vertical

operating position with the locking arm located into the two grooves on

either side of the juicer cover.

Motor appears to stall when juicing

•

Wet pulp can build up under the juicer cover if the juicing action is too

vigorous. Try slower juicing action by pushing the food pusher down more

slowly. Follow cleaning instructions and clean the lter bowl surround, the

juice disc and the juicer cover.

•

The juicer will automatically stop operating if the motor is stalled for more

than 10 seconds. Either too much food is being processed at one time

or the pieces are not small enough. Try trimming the food or cutting into

smaller pieces of even size and processing a smaller amount per batch.

To continue juicing, reset the juicer by pressing the ON / OFF switch on

the control panel to OFF then turn the appliance back on by pressing

ON / OFF switch to ON.

•

Hard fruits and vegetables will put excess strain onto the motor if a low

speed is selected. Please refer to the juicing guide to determine the

correct speed for the fruits and vegetables selected for juicing.

Excess pulp building up the Stainless

Steel Filter Disc

•

Stop the juicing process, remove the juicer cover, scrape o pulp,

reassemble and begin juicing again. Try alternating (soft and hard)

vegetable and fruit varieties.

Pulp too wet and reduced

extracted juice

•

Try a slower juicing action.

•

Remove juice disc and thoroughly clean mesh walls with a cleaning

brush. Rinse the juice disc under hot water. If the ne mesh holes are

blocked, soak the basket in a solution of hot water with 10% lemon juice

to unblock the holes or wash in the dishwasher.

This will remove excess bre build up (from fruit or vegetables) which

could be inhibiting the juice ow.

Juice leaks between the rim of the

juicer cover

•

Try a slower juicing speed and push the food pusher down the feed chute

more slowly.

Juice sprays out from spout

•

Use juice jug and lid provided, or if juicing into a glass use the custom

designed juice nozzle.

•

Try using fruits with more water content to help ush through the contents.

Additionally, try a slower juicing action by feeding one piece in at a time

and by pushing the food pusher down more slowly.

When using the Froojie

extractor, the

lter bowl surround becomes full and

clogs its spout

•

Try using fruits with more water content to help ush through the contents.

Additionally, try a slower juicing action by feeding one piece in at a time

and by pushing the food pusher down more slowly.

Overheating with excessive loads.

•

The juicer is tted with a safety device which safeguards against

overheating with excessive loads. If overheating occurs, the juicer will

automatically activate the overload protection device and the unit will

switch itself o. When the overload protection is activated, unplug the

juicer from the power outlet for at least 15 minutes to allow the unit to cool.

Then plug the juicer into the power outlet and use as normal.

Sage BJE520 - the Nutri Juicer Plus Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sage BJE520 - the Nutri Juicer Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info