Bedienungsanleitung Sage SCP600 (Seite 6 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

714753

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Assembly

ASSEMBLING THE JUICER

1. Pull the juice press arm up, away from the

motor base, until fully extended.

2. Place the juice collector onto the drive shaft on

top of the motor base, ensuring the juice spout

ts into the semi-circular groove at the front

of the motor base.

3. Insert the lter into the juice collector, aligning

the indent with arrow in the bottom of the lter

over the corresponding tab with arrow in the

juice collector.

4. Place the juicing cone onto the drive shaft and

press down lightly to lock the cone into position.

5. To insert the fruit dome, place it into the hole on

the underside of the juice press arm. The fruit

dome is magnetic and will stick into place.

6. Ensure the anti-drip juice spout is pushed

down into the pouring position.

DISASSEMBLING THE JUICER

1. Turn the juicer OFF at the ON/OFF button,

then unplug from the power outlet.

2. Pull the juice press arm up, away from

the motor base, until fully extended.

Close the anti drip spout by flipping it up.

3. Remove the fruit dome by pulling on it gently

to release the magnet

4. Lift the juice collector from the base with the

lter, juicing cone and fruit dome still in place.

Remove the cone and lter from the juice

collector over a sink for easier cleaning. Follow

recommended care and cleaning guidelines.

Functions

1. Ensure the juicer is correctly assembled and

a glass or jug is placed under the juice spout

before juicing.

2. Cut the citrus fruit in half by cutting across the

fruit segments, rather than across the tip ends,

to ensure more ecient juicing.

3. Plug the power cord into a 220–240V power

outlet, then press ON/OFF switch to ON.

4. Place a citrus fruit half, cut side down,

onto the juice cone and push down lightly

onto the spikes.

5. Grasp the handle and slowly lower the juice

press arm. Press down (in a gentle but rm

action) until the fruit dome is in contact with the

fruit skin. The motor will automatically start and

the juicing cone will begin to rotate. The juice

will be extracted from the fruit and ow through

the juice spout into the glass. The pulp and

seeds will collect in the lter.

6. The juicer juices very quickly so each

fruit half will be juiced in a few seconds.

To automatically stop the motor, lift the juice

press arm up to its extended position.

7. Remove the used fruit from the

juicing cone. Empty excess pulp

and seeds from the lter as required.

Repeat Steps 3–7 to continue juicing.

NOTE

The lter should be emptied when full with pulp

and seeds. The lter can be emptied during juicing

by turning the juicer OFF at the ON/OFF switch

and carefully removing the juicing cone and lter.

Clean and replace lter and juicing cone before

continuing to juice. Do not allow the lter to overll

as this may prevent correct operation or damage

the unit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sage SCP600 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info