714736
9
Zoom out
Zoom in
Vorherige Seite
1/128
Nächste Seite
9
EN
ASSEMBLY
5. Place the processing lid onto the
processing bowl so the feed chute is
slightly right of the bowl handle and the
arrow graphics are aligned .
Holding the feed chute and pressing
down rmly at the same time, turn the lid
clockwise (as indicated by the graphic)
so the ‘Locking Tab’ on the lid slots into
the ‘Interlocking Safety Catch’ on the
handle. The lid should be securely locked
into position.
NOTE
The food processor will not operate
unless both the processing bowl and
lid are correctly locked into position.
CAUTION
The processing blade (including
the mini bowl blade) and discs are
extremely sharp, handle with care
at all times.
6. Insert the power plug into a 220–240 volt
power outlet and switch the power
outlet on.
7. At the end of processing, always wait until
the blades or discs have stopped spinning
before unlocking and removing the lid.
To remove the processing lid, ensure the
POWER / OFF button has been pressed,
the power is switched o at the power
outlet and the cord is unplugged from the
power outlet. Holding the feed chute and
pressing down rmly at the same time,
turn the lid anti-clockwise so that the
arrow graphics are no longer aligned.
8. Remove the processing bowl (before
removing blade or discs) by turning it
anti-clockwise until the handle is in line
with the ALIGN HANDLE. Lift the bowl
o the motor shaft. When removing the
discs – carefully remove by gripping the
plastic hub on the centre of the disc and
lifting the disc up and away from the pin
on the spindle.
OVERLOAD PROTECTION SYSTEM
If the motor overloads, the food processor will go
to STANDBY mode and OVERLOAD icon in the
LCD starts to ash. The food processor can still
be switched o by pressing the POWER / OFF
button. To operate the food processor again,
allow the machine to cool for approx 30 minutes.
Some sti mixtures, such as dough, may cause
the dough blade to rotate more slowly than
normal. If this happens, do not process for
longer than 1 minute.
9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Sage SFP800 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info