Bedienungsanleitung Sage SPB620 (Seite 8 von 76) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

714872

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Functions

OPERATION

• The blender will only work when the blades and

cup are correctly assembled. This engages the

safety interlock, and allows the motor to run.

• When the cup and blade assembly is correctly

assembled with ingredients inside, invert cup,

and place onto the motor base using the

alignment graphics.

• To blend, securely hold the cup assembly and

twist clockwise on the base to the ON position.

• When the desired consistency is reached,

turn tumbler anti-clockwise to release

and disengage the motor.

• Do not blend continuously for more than

60 seconds at a time. Allow the motor to rest

for 2 minutes before continuing.

• Do not mill / grind continuously for more than

30 seconds at a time. Allow the motor to rest

and the metal grinding attachment to cool

for 30 seconds before continuing.

• Ingredients can be pulsed by rotating the cup

within the bayonet positions, which will turn

the motor on and o.

• When nished blending, wait a few seconds

for the blades to stop spinning before lifting the

cup assembly o the motor base.

• Invert the cup and allow the ingredients to run o

the blades for a few seconds before unscrewing

blades. Hold by the blade collar, and turn

anti-clockwise to remove.

• For safety, turn the motor base o at the wall and

unplug when nished blending.

• The grinding attachment works in a similar way

to the tumblers. Attach the blades in the same

way, and use either a pulsing action or

continuous blending, as described above.

• The surface of the stainless steel grinding

cup may become too hot to touch if grinding

for longer than 30 seconds. Detach from base

by holding the plastic collar.

OVERLOAD PROTECTION SYSTEM

• The blender is equipped with an internal self

resetting overload protector to protect the motor

from damage under heavy or continuous loads.

If the blender suddenly stops during use,

this protector may have tripped.

• Remove the cup, unplug and leave it to cool

for at least 30 minutes. Do not replace the cup

assembly while cooling as the protector may

reset causing it to start unexpectedly.

• Tripping the protector indicates that the extractor

is being loaded too heavily, or with excessive

continuous use. Reduce the amount of

ingredients used or allow more time in between

blending to prevent it from happening again,

which will help preserve the life of the motor.

• The MAX line is usually a good indicator to

prevent overly heavy loading, however some

especially dense combinations of ingredients

may still strain the motor. If the motor seems to

be straining or running slowly, only operate for

10 seconds at a time, or reduce the amount

of ingredients used. Adding more liquid can

also help to loosen dense mixtures.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sage SPB620 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info