ENGLISH
22
14. Changing the lamp unit
Only replace the old lamp unit with authorised model RL1280A, reference number SAGEM 251691414
The old lamp unit must be recycled (contact your recycling agency to obtain the address of the nearest depot).
1. You must only change the lamp unit, when the appliance is switched off and mains cable disconnected
from the wall socket.
2. Never try to replace the lamp unit immediately after the SAGEM AXIUM™ Home Cinema Screen has
been switched off. Wait at least 1 hour to allow the lamp to completely cool down.
3. Only handle the lamp unit by the holes designed for this purpose. Never touch any wires or the bulb itself.
4. Make sure that you tighten all the screws and do not leave any foreign bodies inside the appliance.
5. Never replace the fuse of a worn-out lamp.
Remove the left-hand panel by turning the bolt a quarter turn with
a coin.
Then pull it towards you.
Unscrew the two thumbwheels holding the worn-out lamp unit.
The two lamp unit screws are "captive" type, meaning that when
unscrewed they remain in the lamp unit.
Pull it towards you holding it between your thumb and forefinger.
Insert the new lamp unit in place of the old one.
Tighten the two thumbwheels linked to the unit.
Never touch the bulb.
Replace the left-hand panel by pressing it slightly until it goes
back into place.
Turn the bolt again by a quarter turn.
1
2
3
4
21
13. Diagnosing Trouble Shooting
Symptoms: Recommended checks:
When first using your SAGEM AXIUM™ Home
Cinema Screen, the red on/off indicator light is not
illuminated.
Check that the mains cable to SAGEM AXIUM™ Home Cinema Screen is
connected to the appliance and the wall socket.
Also check that the switch on the left side of the appliance is pressed in.
The appliance does not light up when the
on/standby button is pressed on the right side
door or remote control
Check that the mains cable to SAGEM AXIUM™ Home Cinema Screen is
connected to the apparatus and the mains socket.
Also check that the switch on the left side of the appliance is pressed in.
There is no picture. If the menus of your SAGEM AXIUM™ Home Cinema Screen are available:
are available: Check that your video appliances are correctly connected and
are active.
Also check that you have selected the correct video source see § 8.4. Check
that your aerial lead is correctly connected. Also check that you have saved
the channels see § 6.3.4. If this is not the case, start a manual or automatic
search. Also check that the switch on the left side of the appliance is
pressed in. The internal temperature indicator light is flashing red: Put your
television set into standby. The lamp condition indicator light is red: the lamp
has gone past its standard working life and may no longer be
functioning. It must be changed.
Black and white picture or picture interference. Check that you have selected the correct video format: e.g. RGB video source
from a DVD player displayed in S-video on your SAGEM AXIUM™ Home Cinema
Screen : check by pressing the picture source selection button if the type of
source selected is compatible with the source emitted.
Check that the colour adjustment is not at minimum.
No sound. Check that the volume is not set at minimum and that mute has not been
activated. Check that your appliances are correctly connected to your SAGEM
AXIUM™ Home Cinema Screen.
Sound weak or discordant during terrestrial reception. Set sound to Mono. Check the "SMART VOL" setting (see § 8.2).
Frozen picture. Check that you have not held the picture: press the “PICTURE of
TELETEXT PAGE HELD” button.
Your appliance does not start on leaving standby
mode when using the button on the right side door
or the standby button on your remote control.
The ON/STANDBY indicator light flashes orange for 20 secs then turns to red or
still flashes orange, switch off the appliance using the switch to the left of your
SAGEM AXIUM™ Home Cinema Screen .Wait 30 secs and restart is using the
normal procedure.
No picture on PIP mode. Check that you have selected sources that is active in PIP mode (see § 8.7).
The remote control is not working normally. Change the batteries.
SAGEM AXIUM™ Home Cinema Screen makes a
hissing noise when switched on.
This noise is normal when starting. It is not considered as malfunctioning.
Pixels on the screen do not light up. In spite of the very high technological precision with which your SAGEM
AXIUM™ Home Cinema Screen has been made, certain pixels may be faulty.
This is not considered as malfunctioning.
