Bedienungsanleitung Salora 24LED9105CD (Seite 54 von 82) (Deutsch, Englisch, Holländisch, Französisch)

594909

Zoom out

Zoom in

Vorherige Seite

1/82

Nächste Seite

English - 52 -

P+P- : More event info

IMPORTANT: Connect a USB disk to your TV while the TV

is switched off. You should then switch on the TV to enable

the recording feature.

Note: Switching to a different broadcast or source is not

available during a recording.

Programme Options

In EPG menu, press the OK button to enter the

Event Options menu.

Select Channel

In EPG menu, using this option, you can switch

to the selected channel.

Set Timer / Delete Timer

After you have selected a programme in the EPG

menu, press the OK button. Select the Set Timer

on Event option and press the OK button. You

can set a timer for future programmes. To cancel

an already set timer, highlight that programme and

press the OK button. Then select “Delete Timer”

option. The timer will be cancelled.

Software Upgrade

Your TV is capable of finding and updating

automatically via the Aerial/Cable/Satellite signal.

Software upgrade search via user

interface

Simply navigate on your main menu. Choose

Settings and select Other Settings menu. In Other

Settings menu navigate on to the Software for

Upgrade item and press OK button to check for a

new software upgrade.

3 AM search and upgrade mode

While the TV is connected to an aerial signal. If

Automatic scanning in the Upgrade Options menu

is enabled, the TV wakes up at 03:00 and searches

broadcast channels for new software upgrades. If

new software is found and downloaded successfully,

the next time the TV powers up , it will have the new

software version.

Note: If the TV fails to come on after the upgrade unplug the

TV for 2 minutes and plug in again.

Troubleshooting & Tips

Tv will not turn on

Make sure the power cord is plugged in securely to

wall outlet. The batteries in the remote control may be

exhausted. Press the Power button on the TV.

Poor picture

• Have you selected the correct TV system?

• Low signal level can cause picture distortion.Please

check antenna access.

• Check if you have entered the correct channel

frequency if you have done manual tuning.

• The picture quality may degrade when two devices

are connected to the TV at the same time. In such

a case, disconnect one of the devices.

No picture

• No Picture means that your TV is not receiving a

transmission. Have you selected the correct button on

the remote control? Try once more. Also make sure

the correct input source has been selected.

• Is the antenna connected properly?

• Is the antenna cable damaged?

• Are suitable plugs used to connect the antenna?

• If you are in doubt, consult your dealer.

No sound

• Has the TV been set to mute? To cancel mute, press the

“” button, or increase the volume level.

• Sound is coming from only one speaker. Is the balance

set to one extreme? See Sound Menu section.

Remote control - does not operate

• The batteries may be exhausted. Replace the

bateries.

Input sources - can not be selected

• If you cannot select an input source, it is possible that

no device is connected. if not

• Check the AV cables and connections if you have tried

to connect a device.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Salora 24LED9105CD Seite 54

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info