Bedienungsanleitung Salus HTR24 (Seite 1 von 2) (Englisch)

735234

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Dial Thermostat

Model: HTR24

INSTALLER MANUAL

SALUS Controls plc

SALUS House

Dodworth Business Park South,

Whinby Road,

Dodworth, Barnsley S75 3SP, UK.

Sales: T: +44 (0) 1226 323961

E: sales@salus-tech.com

Technical: T: +44 (0) 1226 323961

E: tech@salus-tech.com

www.salus-controls.com

SALUS Controls is a member of the Computime Group

Maintaining a policy of continuous product development SALUS Controls plc reserve the right to

change speciﬁcation, design and materials of products listed in this brochure without prior notice.

Issue Date: Dec 2015

00189

For PDF Installation guide please

go to www.salus-manuals.com

8. Technical Speciﬁcation

Warranty

SALUS Controls warrants that this product (HTR24) will be free from any

defect in materials or workmanship, and shall perform in accordance with

its speciﬁcation, for a period of ﬁve years from the date of installation.

SALUS Controls sole liability for breach of this warranty will be (at its option) to repair

or replace the defective product.

Customer Name: ......................................................................................................................................................

Customer Address: .................................................................................................................................................

............................................................................................................................................................................................

....................................................................................... Post Code: ...........................................................................

Tel No: .................................................................... Email: .......................................................................................

Engineers Company: ..........................................................................................................................................

Tel No: ...................................................................... Email: ....................................................................................

Instalation Date: ....................................................................................................................................................

Engineers Name: ...................................................................................................................................................

Engineers Signature: ...........................................................................................................................................

6. Protection Function

7. Control Patterns

5. Thermostat Functions

NSB (Night SetBack) Function

NSB Mode depends on the NSB wired connection.

0V = NSB OFF

24V= NSB ON

The NSB signal is activated every 1 second. When the signal is received the

setpoint temperature will be set at ±2°C or ±4°C.

Heating and Cooling Selection

The Heating/Cooling function is determined by the CO terminal connection.

CO 0V = Heat mode

CO 24V= Cool mode

Cooling Blocked function

Cooling Enabled:

Set the jumper on ON . The thermostat will run in normal cooling mode.

That means that it will open/close the actuators when necessary. The LED will be

BLUE when the cooling function is running.

Cooling Disabled:

Set the jumper on OFF . The actuator will be closed and the LED will

be oﬀ.

Heat cut o at high/low temperature:

When room temperature is over 36°C or under 4°C, all heating/cooling outputs

will be turned oﬀ.

Short cycle protection:

When Cooling Mode is enabled the minimum interval between Relay ON/OFF

is 3 minutes.

Valve Protection:

Set the jumper on ‘ON’ to disable the function or on ‘OFF’ to enable it. Turn on the

valve for 5 minutes every week to prevent any damage to the valve.

Sensor Malfunction:

If the temperature sensor or temperature sensor compensation is open the LED

will ﬂash BLUE/RED alternatively.

If CO terminal is connected and the Heating Mode is ON, the PWM function

will be activated.

If CO terminal is disconnected and the Cooling Mode is ON the ON/OFF control

output will be activated.

Model: HTR24

Voltage:

24 V AC, +-10%, 50/60 Hz

Operating Performance:

24 V: 1,8 W

Temperature setback:

Temperature range:

2°C-4°C

5°C- 30°C

Span:

+/- 0,5°C

Calibration:

Yes, with jumper

Storage temperature:

-20°C to +60°C

Ambient temperature:

0 °C up to 45 °C

Degree of protection:

IP 30

CE conformity according to:

Class II ( EN60730 )

Housing material:

PC, V2

Color:

RAL 9010 pure white

Connection:

Screw terminal

Weight

90g net / 135g gross

Puls-wide-modulation:

(PWM)

Yes

Valve protection:

Heating and Cooling:

Cooling blocked:

Dimensions:

Yes

Yes, automatically Change Over on the CO terminal

Yes, with jumper

85mm*85mm*25mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Salus HTR24 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Salus HTR24

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info