Bedienungsanleitung Salus TRV10RFM (Seite 1 von 2) (Englisch)

735223

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Icons used in this manual:

Safety

Important info

Contents:

Box Contents

Introduction

Product Compliance and

Safety Information

Installation

User Interface

Status/LED indication

Installers notes

Warranty

Innholdet i esken

Product Compliance & Safety Information

INTRODUCTION

The TRV10RFM is a battery-powered, mini-size thermostatic radiator valve (TRV)

controller using ZigBee wireless communication. Simply replace the existing,

passive head on the standard radiator valve with the TRV10RFM (referred to from

now on as the unit). Use the unit with the VS10RF or VS20RF series of wireless

thermostats and a Universal Gateway.

VS10RF / VS20RF

Thermostat

(Required)

UG600

(Required)

SALUS Wiring Centre

KL08RF

Checking the compatibility of your heating system

Our RA adapter also ts this valve.

Once tted the RA adapter should look like this.

If you can not see any thread on

the valve and it looks like this

picture, you may be able to use the

RA adapter supplied.

TRV10 ts 30x1,5 mm thread.

Installing the Unit

Screw the units nut (nger

tight) to the radiator valve

and check that the LED is

solid red.

Press any button on the

unit to adapt it to the

radiator valve. Once all

adaptation noise and LED

activity has stopped, the

unit is ready to pair with

your wireless thermostat.

The unit is now ready

for pairing to the SALUS

thermostat. You may now

start the pairing process.

4 5 6

Remove the battery door

on the side of the unit.

Insert the batteries,

ensuring correct

orientation.

1 2 3

The LED on the unit ashes

green then ashes red before

changing to solid red. When

it is solid red, place the unit

over the radiator valve using

the mounting ring if needed:

Contents of the box

For the latest PFD Instruction Manual, go to

www.salus-controls.com

TRV10RFM

2 AA Batteries

Adapter

Manual

Box Contents

Product Compliance

This product is CE compliant and meets the following EC Directives: Electro-Magnetic Compatibility

directive 2014/30/EU; 2014/53/EU and 2011/65/EU.

Safety Information

Use in accordance with the regulations. The unit is to be used for the control of room temperature

inside the house.

Installation

This accessory must be tted by a competent person, and installation must comply with the

guidance, standards and regulations applicable to the country or state where the product is

installed. Failure to comply with the relevant standards could lead to prosecution.

RX10RF

(Optional)

System Overview

To achieve the best control from the unit and thermostat, we recommend they are

used with the SALUS system receiver congured to RX1. The system receiver will

turn the boiler on or o when requested by the thermostat. See your boiler receiver

manual for more information about the RX1 conguration.

Up to 6 units can be connected to a VS10RF/VS20RF

The unit is modulating, which means it opens or closes partially

or 100% depending on the relationship between the actual room

temperature and the required room temperature measured by

the VS10/20RF.

Checking the compatibility of your heating system

The SALUS TRV10RFM is compatible with the majority of thermostatic radiator valves.

Before tting, please check your valve is suitable for use with the SALUS TRV.

Valve

Remove the TRV head

Note: If all the measurements are as stated on this page then the TRV will t directly

to your valve. Also if your valve is not suitable please consider changing your existing

valves, contact your installer.

Measure the thread diameter

(must measure 30mm)

mm102030

Measure the pin length of the valve

when it is in the open position.

(must measure between 13-16mm)

Preparing to Pair the Unit

Press and hold the button on the Universal Gateway for

ve seconds. This puts the Universal Gateway in pairing

mode. See your Universal Gateway manual for more

information.

Ensure the wireless thermostat is powered up and

ready for pairing. See your thermostat manual for more

information.

If you are using the optional RX10RF wireless boiler receiver congured for

remote boiler switching, ensure this has been powered up and the red LED

has gone from ashing to steady. See your boiler receiver manual for more

information.

Pairing the Unit

Press and hold the pairing button for 10 seconds.

You can pair up to 6 units with one thermostat.

Pair the units room by room.

You have paired the unit to the thermostat when the unit LED goes off.

Once paired, the unit operates in automatic mode and receives room temperatures

from the thermostat.

LED Indication

Pairing Button

Manual open/

status indication

Manual close/

status indication

Using the Unit

Leaving the Network

Once paired to a thermostat, press and hold the

pairing button on the unit for 10 seconds.

The red LED come on together for one second.

Note: After you have deleted the unit from the

wireless network, you must reinstall the TRV see

Installing the unit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Salus TRV10RFM Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info