Bedienungsanleitung Samson D-2500 (Seite 17 von 32) (Englisch)

629999

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Operating the D2500

Using the Internal LIMITER for Basic Speaker

Protection

In order to help you protect your speaker system, the

D2500 employs a digital Limiter. The D2500's Limiter is a

brick wall type with a very fast attack time and a very slow

release time. When engaged, the digital Limiter will pre-

vent signals from reaching outputs levels over a desired

point. The D2500’s Limiter has a variable Threshold level,

which is the point the limiter circuit begins to attenuate

the system. The Limiter also has a variable Release time,

which is the time the limiter circuit takes to return the sig-

nal to the original level.

The LIMITER Switch Has Two Clicks!

Click Menu Function

Value

1 Lim. Thr. Threshold

0 to -100 dB

Lim. Rel.

Release Time

50 to 100 %

To operate the D2500 digital LIMITER follow these simple

steps.

• Press the LIMITER switch so that the yellow LED is lit.

• Now, engage the effect by pressing the IN / OUT switch

until the yellow LED lights.

• To access the Threshold parameter, press the LIMITER

switch until you see the menu, Lim. Th. The LIMITER

Threshold can be set from –100 dB to 0 dB.

• To access the Release parameter, press the LIMITER

switch until you see the menu, Lim. Rel. The LIMITER

Release time can be set from 50 to 100

%, which is the

equivalent to 2 to 15 seconds















Using the A/B Feature

The A/B switch lets you compare the actual, modified

program to the last program recalled or stored in memory.

After you load a preset you may want to make some

changes to the equalization curve or perhaps to one or

more of the digital effects. Once you make some changes

you may want to compare the edit with the original pre-

set saved in memory. You can compare the current set

with the preset that is stored in memory by using the A/B

switch. Try the A/B function to compare and preset to an

edit by following these steps:

• Press the LOAD switch and select any preset, then press

LOAD again to recall the preset into memory.

• Play some music through the D2500.

• Now change the position of the faders so you can hear

the equalization curve change.

• At this point you will notice that the green LED on the

A/B switch is lit, indicating that there has been a change

to the original preset.

• Now, press the A/B switch again and the green LED will

flash indicating that the D2500 has now returned all the

EQ faders and effects parameters back to the positions

that were saved in the presets. You can continue to press

the A/B switch to toggle back and forth between the

saved preset and the new sound.

If you like the new edited preset you can use the STORE

function to save the new preset either under the current

memory location or a new one.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samson D-2500 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info