Bedienungsanleitung Samson D-2500 (Seite 23 von 32) (Englisch)

629999

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Using the D1500 with the D2500

In order for the D1500 and D2500 to communicate with

each other it is necessary to configure the MIDI param-

eters so that the units are communicating properly. Follow

the steps below to configure the MIDI parameters for

communication between one D1500 RTA and one D2500

Digital EQ. Let's start with the D1500:

• Press the MIDI switch until you get to the “MIDI” screen

and use the DATA WHEEL to select “ON.”

NOTE: You may notice the MIDI light flashing which is indi-

cating that you are editing the MIDI set up.

• Now, press the MIDI again and set the MIDI CHANNEL

number to “1”.

• Press the MIDI switch once again and use the DATA

WHEEL to set the “OMNI” mode to “OFF”.

• Next, you need to configure the D1500 to transmit and

receive MIDI System Exclusive messages, so press the

MIDI switch again and use the DATA WHEEL to set the

SysEx to select “T+R”.

• Press the MIDI switch once again and use the DATA

WHEEL to set the “Pgm Ch.”(MIDI Program Change) to

“OFF”.

• Once you have all the parameters set, press the STORE

button to save the changes to the MIDI set up.

• Now, Let's set up the D2500.

• Press the D2500's Global switch a few times until the

display reads: F.R.

• Now,

turn the Data Wheel until the dispay reads +/-12

dB.

• Press the D2500's Global switch a few times until the

display reads: F.Bw.

• Then,

turn the Data Wheel until the display reads 1/3

Oct.

• Press STORE to confirm the Global changes.

• Press the MIDI switch until you get to the “MIDI”

screen and use the DATA WHEEL to select “ON.”

NOTE: You may notice the MIDI light flashing which is

indicating that you are editing the MIDI set up.

• Now, press the MIDI again and set the MIDI CHANNEL

number to “1”.

• Press the MIDI switch once again and use the DATA

WHEEL to set the “OMNI” mode to “OFF”.

• Next, you need to configure the D1500 to transmit and

receive MIDI System Exclusive messages, so press the

MIDI switch again and use the DATA WHEEL to set the

SysEx to select “T+R”.

• Press the MIDI switch once again and use the DATA

WHEEL to set the “Pgm Ch.”(MIDI Program Change) to

“OFF”.

• Once you have all the parameters set, press the STORE

button to save the changes to the MIDI set up.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES

CLASS B

. OPERATION IS SUBJECT TO THE FOLLOWING TWO

CONDITIONS: (1) THIS DEVICE MUST NOT CAUSE HARMFUL

INTERFERENCE

, AND (2) THIS DEVICE MUST ACCEPT ANY

INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT

MAY C

AUSE UNDESIRED OPERATION.













Operating the D2500 with the D1500 RTA

The diagram above shows the MIDI connections for using a D1500 RTA with a D2500

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samson D-2500 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info