Bedienungsanleitung Samson Expedition XP1000 (Seite 10 von 112) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

623997

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

XP1000 Mixer Layout

5. Equalizer control knobs

HIGH Frequency – The HIGH knob controls the amount of treble applied to each

channel. The channel’s high frequency response is flat when the knob is in the cen-

ter detent (12:00) position. Rotating the knob to the right will boost the channel’s

high frequency response above 10 kHz by 15 dB, and rotating it towards the left

will cut the high frequency response by 15 dB.

LOW Frequency – The LOW knob controls the amount of bass applied to each chan-

nel. The channel’s low frequency response is flat when the knob is in the center

detent (12:00) position. Rotating the knob to the right will boost the channel’s low

frequency response below 100 Hz by 15 dB, and rotating it towards the left will cut

the low frequency response by 15 dB.

6. EFFECTS switch - Use the EFFECTS switch to add an effect to a Mic or Line input on

any of the first four input channels. The EFFECTS indicator lights GREEN when the

channel EFFECTS switch is ON.

7. LEVEL knobs - This knob sets the overall level for the input channel.

NOTE: To reduce noise, set the LEVEL controls on any unused channels to the mini-

mum setting.

8. Stereo Channel Input Jacks (channels 5/6, 7/8, 9/10) - For stereo inputs, use the L

input to connect the left channel and the R input to connect the right channel.

Use these inputs to connect high impedance microphones, synthesizers, drum

machines, MP3, CD, tape players or any other line level device. The XP1000 fea-

tures ¼” phone,

” phone, and RCA connectors.

9. MONITOR OUT jacks - The signal present at the MONITOR OUT jacks is sent from the

MONITOR level control knob, which is fed from the input channels. The MASTER

control does not affect the MONITOR OUT signal. This output can be used to send

the mix to powered speaker cabinets to use a stage monitors, or as additional front

of house speakers to expand the coverage of the system.

10. REC OUT jacks - This output is used to send the main mix to an external recorder.

The signal present at this connector is the L/R bus signal before it has passed

through the MASTER level control. The nominal output level is -10 dBV and the

impedance is 600 Ohms.

11. SPEAKER OUT jacks - Two ¼” phone powered output jacks used to connect the left

and right speakers. Use the included speaker cables to connect the speakers.

CAUTION: The total impedance load for each side of the amplifier must not be less

than 4 Ohms. Do not connect additional speakers to the XP1000 mixer/amplifier.

12. AC Input – Connect the supplied heavy-gauge 3-pin “IEC” power cable here.

13. POWER switch - Use the POWER switch to turn power to the XP1000 on or off. The

switch illuminates red when the unit is in the ON position and receiving power.

14. SPEECH/MUSIC switch - The SPEECH/MUSIC switch is used to change the overall

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samson Expedition XP1000 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info