Bedienungsanleitung Samson Expedition XP800 (Seite 9 von 92) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

624002

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

XP800 • Portable PA System

ENGLISH

FRANÇAISDEUTSCHEESPAÑOLITALIANO

Mixer Layout

will cut the high frequency response by 15 dB.

LOW Frequency – The LOW knob controls the amount of bass applied to each chan-

nel. The channel’s low frequency response is flat when the knob is in the center

detent (12:00) position. Rotating the knob to the right will boost the channel’s low

frequency response below 100 Hz by 15 dB, and rotating it towards the left will cut

the low frequency response by 15 dB.

6. EFFECTS Knobs – Use the EFFECTS control knows to add an effect to a Mic or Line

input on any of the first four input channels. As the knob is rotated clockwise, the

level of signal sent to the effects bus is increased.

7. LEVEL Knobs – This knob sets the overall level for the input channel.

NOTE: To reduce noise, set the LEVEL controls on any unused channels to the mini-

mum setting.

8. Stereo Channel Input Jacks (channels 5/6, 7/8) – For stereo inputs, use the L input to

connect the left channel and the R input to connect the right channel. Use these

inputs to connect high impedance microphones, synthesizers, drum machines,

MP3, CD, tape players or any other line level device. The XP800 features ¼”

phone,

” phone, and RCA connectors.

9. MONITOR OUT Jacks – The signal present at the MONITOR OUT jacks is sent from

the MONITOR level control knob, which is fed from the input channels. The

MASTER control does not affect the MONITOR OUT signal. This output can be

used to send the mix to powered speaker cabinets to use a stage monitors, or as

additional front of house speakers to expand the coverage of the system.

10. SUB OUT Connector – This full-range output is used to send the main mix to an

external active subwoofer. The signal present at this connector is the after the

MASTER level control.

11. FOOT SW Jack – Connect a footswitch to this jack to turn on and off the on–board

digital effects.

12. SPEAKER OUT Jacks – Two ¼” phone powered output jacks used to connect the left

and right speakers. Use the included speaker cables to connect the speakers.

CAUTION: The total impedance load for each side of the amplifier must not be less

than 8 Ohms. Do not connect additional speakers to the XP800 mixer/amplifier.

13. AC Input – Connect the supplied heavy gauge 3-pin “IEC” power cable here.

14. POWER Switch – Use the POWER switch to turn power to the XP800 on or off. The

switch illuminates red when the unit is in the ON position and receiving power.

15. MONITOR Level Knob – The MONITOR level control is used to control the overall level

sent to the MONITOR OUT.

16. Pairing Indicator – Displays the Bluetooth

status of the XP800 system.

17. Pairing Button – Press this button to enable discoverable mode in order to pair with

a Bluetooth audio device.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samson Expedition XP800 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info