Bedienungsanleitung Samson Graphite 25 (Seite 24 von 36) (Englisch)

630024

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Performance Controls

The Graphite 25 features eight assignable encoders (E1–E8), volume slider (S1), four function but-

tons (F1–F4) and transport controls. Below is a brief description of how these features operate.

Encoders

The factory setting for the encoders is pan control, set to channels 1–4. When you rotate the

knob of an encoder, the encoder number and the data will be shown in the Operation area of the

display. Rotate the knob clockwise to increase the value, and counter-clockwise to decrease the

value (ranging 0–127). You can change parameters or assign other controls to encoders in “Setup

Mode” on page 17. The default settings for encoders are listed in “Factory Default Settings” on

page 31.

Slider

The factory setting for the slider is master volume. When you move a slider, the slider number, S1,

and the data will be shown in the Operation area of the display. Move the slider to the right to

increase the value, and to the left to decrease the value (ranging 0–127). You can change param-

eters or assign other controls to encoders in “Setup Mode” on page 17.

Note: Assign the Channel to “-“ for the slider and encoders to follow the keyboard channel of Zone 1.

Function Buttons

There are four function buttons (F1–F4) on the control panel. The buttons can be dened as

“Note” type (abbreviated to N), which send note messages when pressed, or “Control” type (ab-

breviated to C), which send control messages when pressed.

The buttons can also be set to “Toggle” (abbreviated to 0). Press one of the buttons to send the

On message, and press the button again to send the O message. The buttons can alternatively

be set to “Momentary” (abbreviated to M). If the button is a control type, press the button to send

the control code. When you release the button, the control code will no longer be sent. If the type

of the button is a note type, press the button to send note on message and release the button to

send a note o message.

The button number and value will be shown in the Operation and Data area of the display. The

function of each button is assignable. You can change parameters or assign other controls to

buttons through the setup function. Please refer to “Setup Mode” on page 17 for details. The

default settings for the function buttons are listed in “Factory Default Settings” on page 31.

BANK Buttons

There are four banks of encoders and function buttons with individual settings, expanding the

amount of controls available. The BANK buttons allow you to group the settings of the encoders

E1–E8 and function buttons F1–F4 into a bank, and then recall them quickly. Press the BANK ◀ /

▶ buttons to select between the banks. The bank number will be shown under the BANK tag in

the display. The default bank is 1.

CHANNEL Buttons

Press the CHANNEL ◀ / ▶ buttons to increase or decrease the channel number for all encoders

E1–E8 and function buttons F1–F4 in the activated bank, to quickly expand the working range,

globally. The channel change message will be handled by the computer software when a soft-

ware preset is selected, and the icon “-“ will be displayed under the Ch +/– tag.

Note: When the remote control preset (Preset 2–10) is activated, the BANK and CHANNEL buttons will

send specic control messages to the music software.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samson Graphite 25 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info