Bedienungsanleitung Samson L1200 (Seite 20 von 24) (Englisch)

624004

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Getting Started with MAC OS X - continued

5. Next, click in the Output tab and select USB Audio

Codec (figure 11). You may notice that the Volume

slider sets itself to the full level. This will allow you

to have full range using the L Series’ hardware MAIN

Volume control.

At this point you can begin using your L Series console

with most any audio recording software, but you need

to select it as an input and output device within the

DAW. When selecting the inputs and outputs just look

for and select the USB Audio Codec.

Recording from the L Series’ USB I/O

A - SEND - switch

The USB SEND switch is used to select the mix out-

put that is sent to the internal AD (analog to digital)

converter and then out the USB socket and then on

to a PC. The switch allows you to select either the

MAIN Left and Right or AUX 1 / 2 outputs.

For recording a live performance, you can send the

MAIN Left and Right mix signal to the USB out for

recording exactly the same mix as you hear in the

sound system.

Be sure that the USB SEND switch is set to MAIN (up

position) to send the MAIN Left and Right mix to the

USB input.

The USB I/O is always active and it will send a stereo

signal based on the position on the USB SEND

switch. When the USB SEND switch is set to MAIN,

the signal sent to the computer will be comprised

of the input channels that are assigned to the MAIN

Left and Right Bus. The mix level follows the channel

FADER and the stereo image set by the channel’s

PAN control. You can also assign the USB out to feed

from the AUX1 and AUX2 outputs enabling you to

build a stereo mix for recording that’s independent

from the house sound system. Press the USB SEND

Figure 11

switch down to send the AUX1 and AUX2 mix to

the USB input.

Playing Back From the L Series’ USB I/O

B - RETURN - switch

The USB RETURN switch is used to route the signal

presented to the internal DA (digital to analog)

converter, that’s been received from a USB digital

audio connection typically from a PC. The RETURN

switch allows you to select a return either directly

to the MAIN Left and Right mix or the last stereo

channel (channels 11/12 on the L1200 and 19/20 on

the L2000).

For playback, you can return the USB stereo signal

directly into the Main left and right mix bus so that

the playback from the PC sums with the MAIN mix

on the console.

You can also use the USB RETURN switch TO route

the signal from the USB output to the last stereo

channel.

To hear the USB playback in the MAIN mix, be

sure that the USB SEND switch is set to MAIN (up

position).

For added flexibility, you can assign the USB stereo

playback signal to the last stereo channels (11/12

on the L1200 and 19/20 on the L2000). This gives

you the ability to mix the signal in the MAIN mix,

and also, you can assign to the Auxiliary sends and

Bus outputs so you can mix the playback in floor

monitors or isolate the playback to a mix zone. Press

the USB RETURN switch down to return the USB

input to the last stereo input.

C - MONITOR – switch

The MONITOR switch is use to assign the USB return

to the headphones. Press the USB MONITOR switch

down if you want to hear the USB playback in the

headphones.

Using the USB I/O

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samson L1200 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Samson L1200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info