Bedienungsanleitung Samson L3200 (Seite 13 von 28) (Englisch)

624007

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Controls and Functions

42 - PHONES – control knob

This control adjusts the overall level of the

Headphone Output.

43 – PFL DEFEAT – switch

You can defeat all the channels in PFL by using the

PFL DEFEAT switch. When the switch is pressed

down it will illuminate, indicating the PFL and AFL

are temporarily turned off. At that point you will

hear the MAIN mix in the headphones until the PFL

DEFEAT is turned off and you will now hear the SOLO

bus again in the headphones.

USB I/O Section

The L series consoles incorporate a sophisticated

USB I/O with on board AD and DA converters

providing a digital audio path for connecting to a

PC running most any recording and/or playback

software. The INPUT and ASSIGN switch give you

added flexibility in routing the digital audio signal to

and from the PC.

44 – SEND – USB input send switch

The USB INPUT switch allows you to select one of

two stereo (or two channel) signal paths to feed the

USB output to send to the connected PC. When the

INPUT switch is in the up position, the USB signal will

feed from the MAIN left right mix. When the INPUT

switch is in the down position, the USB signal will

feed from the AUX 1 and AUX 2 buses which enables

you to create a unique mix to send to the PC.

45 – RETURN – USB return switch

The USB RETURN switch allows you to select one of

two stereo return paths to receive USB audio from

the connected PC. When the ASSIGN switch is in the

up position, the USB signal will return to the MAIN

mix bus. When the ASSIGN switch is in the down

position, the USB signal will return to the last pair

of stereo channels which enables you to playback a

recorded

track in the MAIN mix, and you can use the channels

AUX sends to feed any of the AUX buses. This will

let you hear the USB playback tracks in the monitor

mixes.

46 – MONITOR – USB headphone enable switch

Press the USB MONITOR switch down if you want

to hear the signal from the USB return in the

headphones.

Meter Section

47 - CLIP LEDs

The left and right CLIP LED’s illuminate when the

signal from the selected bus is beginning to reach

a level where distortion occurs. If the CLIP lights

stay on, your mix is too hot and you need to lower

the level control. It is okay for the PEAK light to

occasionally light, however they should go off

quickly and not stay on.

48 - LED VU METER

The OUTPUT LEVEL METER allows you to monitor

the level of the signal, which is being sent to the

MIX OUT jacks. Depending on the position of the

Meter select switch, the meters will display the MAIN

MIX with PFL and AFL, or display the level from the

GROUP 1–4 outputs.

49 - PFL/AFL LED - indicator

The LED will illuminate whenever any PFL or AFL

switch is pressed.

50 – Meter select switch

The Meter select switch allows you to configure the

Meters for MAIN MIX with PFL and AFL, or to display

the level from the GROUP 1–4 outputs. When the

METER select switch is up, the MAIN MIX, PFL and

AFL are displayed. When the METER select switch is

down, the GROUP output are displayed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samson L3200 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info