Bedienungsanleitung Samson MDR16 (Seite 18 von 32) (Englisch)

24757

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Microphone Input - Mono Input Channels

Use these inputs to connect Low Impedance microphones and low level signals from direct boxes. The MIC inputs have a nomi-

nal operating level of -62dB through -8dB. The MIC inputs also feature +48V phantom power, allowing you to use condenser

microphones. The Phantom Power switch (located on the MDR16’s rear panel) enables phantom power on all the microphone

inputs when set to the ON position. XLR Connector pin-out - Pin 1: Ground, Pin 2: Hot (+), Pin 3: Cold (-)

Line Level Input - Mono Input Channels

Use these inputs to connect line level signals from synthesizers, drum machines, effects processors or any line-level signal. The

LINE inputs have a nominal operating level of -27dB through +27dB. TRS phone jacks. Connector pin-out - Sleeve: Ground, Tip:

Hot (+), Ring: Cold (-)

INSERT- Mono Input Channels

Send and return patch point on TRS (TIP/RING/SLEEVE) jack for interfacing external effects processors.

Stereo/ Dual Mono Input Channels

The MDR16’s channels 9 – 16 can be used for either four stereo inputs or eight mono inputs. These channels feature a combi-

nation XLR and 1/4 inch connector, often referred to as a “combie” connector, to handle both the LINE and MIC inputs. The LINE

input is located in the center of the combie connector. You can connect the outputs from devices such as synthesizers, drum

machines, effects processors or any line-level signal. The LINE inputs have a nominal operating level of -27dB through +27dB.

The TRS phone jacks Connector pin-out is; Sleeve: Ground, Tip: Hot (+), Ring: Cold (-). The MDR16’s stereo/dual mono chan-

nels have a utility MIC input located on the combie connector. The utility MIC inputs have a nominal operating level of -40dB.

The MIC inputs also feature +48V phantom power, allowing you to use condenser microphones. The Phantom Power switch

(located on the MDR16’s rear panel) enables phantom power on all the microphone inputs when set to the ON position. The

XLR Connector pin-out is; Pin 1: Ground, Pin 2: Hot (+), Pin 3: Cold (-).

Odd Channel (Left) Mic/Line Input

If you want to use the Stereo/Dual Mono channels for stereo you would connect the left side to the odd numbered channel.

When using the inputs for stereo signals, be sure to set the pan knob all the way to the left to maintain the stereo balance. Of

course, you can connect any mono signals here as well. Channels 11 through 16 are configured the same as 9 and 10.

Odd Channel (Left) Mic/Line Input

If you want to use the Stereo/Dual Mono channels for stereo you would connect the right side to the odd numbered channel.

When using the inputs for stereo signals, be sure to set the pan knob all the way to the right to maintain the stereo balance. Of

course, you can connect any mono signals here as well. Channels 11 through 16 are configured the same as 9 and 10.



























































MDR16 Input and Output Connections

CHANNEL 1–8 MIC and LINE INPUTS

The MDR16’s input channels 1 - 8 each have an XLR MIC level, Low-Z (Low Impedance) input and a 1/4-inch LINE level, Hi-Z (High

Impedance) input. By using the GAIN control on channels 1- 8, you can connect a variety of signal sources from microphones and

direct boxes to line level devices such as synthesizers and drum machines. All the LINE and MIC inputs are balanced. The MIC inputs

are compatible with microphones with output impedances of 50~600 Ohms and the LINE inputs are compatible with line level devic-

es of 600 Ohms.

NOTE:

It is not possible to simultaneously use both the LINE and MIC inputs on the same channel (with the exception on the stereo

input channels). Use only one of the inputs for the appropriate source for each channel.

Following below is a detailed description of the MDR16’s input and output connectors.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samson MDR16 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info