Bedienungsanleitung Samson Resolv A8 (Seite 12 von 16) (Englisch)

630017

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Operating the Resolv A Series

Resolv A Series Control Panel - continued

HIGH FREQUENCY LEVEL CONTROL

The four-position High Frequency Level control switch is used to adjust the monitor's high-frequency

response, providing four equalization curves to select from. By using the High Frequency Level con-

trol, the Resolv A Series’ high frequency response is adjusted with the application of a high-end tilt

(equalization circuit) centered at 12kHz, with selectable levels of –3dB, 0dB (flat), + 3dB and +6dB. You’ll

find that the change is very subtle. Many mix engineers prefer the sound of near field monitors with a

little lift in the high frequency response, some like more focus on the midrange, and therefore, desire

a flatter or rolled off high frequency response. The best way to set the controls is what sounds good to

you. Therefore, you should experiment with the various settings to find the combination of the High

Frequency Level and Volume controls you like. To do this, play several CD’s of music that you are familiar

with. Remember, if you think you’re getting lost, the Resolv A Series is flat when the High Frequency Level

control is set to the “0” position.

VOLUME CONTROL

The volume control is used to adjust the

overall output level of the Resolv A Series.

When operating the unit for the first time,

start with the volume control set all the

way off. Slowly raise the Volume control

to reach a comfortable listening level.

The Ins and The Outs

The Resolv A Series features a full comple-

ment of input connectors providing easy

installation with a variety of audio devices

like recording consoles, hard disk record-

ers, CD players and computer sound

cards, to name a few. The following sec-

tion details the Resolv A Series's input

connectors. In addition, there is a detailed

cable-wiring diagram on page 12.

BALANCED XLR AUDIO INPUT (A6 and

A8 only) - The Resolv A Series features a

female XLR connector that will accept bal-

anced or unbalanced +4dBU line level sig-

nal. If you are using a mixer that has bal-

anced outputs on XLR connectors, you can make the connections via standard XLR (microphone) cable.

1/4-INCH PHONE AUDIO INPUT – A balanced TRS (Tip, Ring, Sleeve) 1/4-inch phone plug is used to con-

nect balanced or unbalanced line level signals. The 1/4-inch input is a switching jack, so when a 1/4-inch

connector is inserted into the jack, the RCA and/or XLR inputs are switched off and the 1/4-inch input

is switched on. This provides a convenient patch-point for quick insertion of a secondary input signal

source for testing or expanded operation.

RCA AUDIO INPUT – The RCA input accepts unbalanced signals used to connect signals from unbal-

anced –10dBV devices.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samson Resolv A8 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info