Bedienungsanleitung Samson S-Zone (Seite 8 von 108) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

629661

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

INPUT SECTION

1 VOLUME – Rotary control used to adjust the level of

signal source connected to channel 1.

2 ZONE 1 – When the LED Backlit switch is pressed

in, the switch lights red and the input is assigned to

ZONE 1.

3 ZONE 2

– When the LED Backlit switch is pressed in,

the switch lights green and the input is assigned to

ZONE 2.

4 STEREO/MONO

switch - This switch is used to

select either stereo or mono input.

5 SCRIBE STRIP

– Convenient area for marking the

input source allowing you to label the channel with

the device connected to the input.

6 ZONE 3

– When the LED Backlit switch is pressed in,

the switch lights amber and the input is assigned to

ZONE 3.

7 ZONE 4 – When the LED Backlit switch is pressed in,

the switch lights orange and the input is assigned to

ZONE 4.

8 MIC/LINE 2 – Channel 2 input with the same knob

and switch complement as Channel 1.

9 LINE 3 – Channel 3 input with the same knob and

switch complement as Channel 1.

10 LINE 4 – Channel 4 input with the same knob and

switch complement as Channel 1.

MONITOR SECTION

11 MONITOR SPEAKER – This built-in, miniature super-

speaker allows you to listen to the signal that is pres-

ent at any ZONE OUTPUT.

12 MONITOR VOLUME

- This rotary control is used

to adjust the monitor level heard in the front panel

Headphone jack or SUPER SPEAKER.

Controls and Functions

Front Panel Layout

13 ZONE SELECT switch – This four-position switch is

used to assign any of the four Zones to play in the

MONITOR SPEAKER or HEADPHONE JACK.

14 HEADPHONE JACK

- Connect any standard stereo

headphone using a standard 1/4-inch jack to moni-

tor the ZONE OUTPUTS.

ZONE OUTPUT SECTION

15 VOLUME

– This rotary control is used to control the

overall level of OUTPUT ZONE 1.

16 HIGH

– High frequency equalizer rotary control

with +/-12 dB of cut or boost at 10kHz.

OUTPUT METER – Six-segment LED meter display-

ing the level of the ZONE 1 OUTPUT with -20 to +14

dB indicators.

18 STEREO/MONO switch

- This switch is used to

select either stereo or mono operation on the ZONE

1 OUTPUT.

19 SCRIBE STRIP

– Convenient area for marking the

ZONE OUTPUT allowing you to notate the room or

area the zone is feeding.

20 LOW– Low frequency equalizer rotary control with

+/-12 dB of cut or boost at 100Hz.

21 ZONE OUTPUT 2 – ZONE 2 OUTPUT with the same

knob and switch complement as ZONE 1 OUTPUT.

22 ZONE OUTPUT 3 – ZONE 3 OUTPUT with the same

knob and switch complement as ZONE 1 OUTPUT.

23 ZONE OUTPUT 4 – ZONE 4 OUTPUT with the same

knob and switch complement as ZONE 1 OUTPUT.

24 POWER switch

– Use this switch to power the unit

on and off.

   





    



  

    

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samson S-Zone Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info