Bedienungsanleitung Samson Stage 5H (Seite 8 von 12) (Englisch)

623984

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Setting Up and Using Your

Stage 5 Series System

(consult the owners manual of your mixer and/or amplifier for details). If you still hear distortion,

do the following:

• The HT5 transmitter's Gain control has been factory preset to provide optimum level for the

particular microphone model being used and so no adjustment should be necessary. Any

distortion present should therefore simply be a matter of the microphone being too close to

the mouth; try moving it further away. If this does not solve the problem, use the supplied

plastic screwdriver to turn the Gain control (trimpot) on the HT5 slowly counterclockwise until

the distortion disappears.

Note that, following this setup procedure, you can always lower the Volume knob of the SR5 in

order to further attenuate the output signal if necessary.

11. Conversely, if you hear a weak, noisy signal at the desired volume level (and with the Volume

control of the receiver turned fully clockwise), again make sure that the SR5 rear panel Audio

Output Level switch is set correctly and that the gain structure of your audio system is correctly

set. If it is and the signal coming from the SR5 is still weak and/or noisy, do the following:

• The HT5 transmitter's Gain control has been factory preset to provide optimum level for the

particular microphone model being used and so no adjustment should be necessary. Any

weakness of signal should therefore simply be a matter of the microphone being too far from

the mouth; try moving it closer. If this does not solve the problem, use the supplied plastic

screwdriver to turn the Gain control (trimpot) on the HT5 slowly clockwise until the signal

reaches an acceptable level.

12. Temporarily turn down the level of your mixer/amplifier system and turn off the power to

your transmitter, leaving the SR5 on. Then restore the previously set level of your mixer/amplifier.

With the transmitter off, the receiver output should be totally silent—if it is, skip ahead to the

next step. If it isn’t (that is, if you hear some noise), you may need to adjust the receiver’s front

panel Squelch control. When the Squelch control is at its minimum setting, the Stage 5 Series

system always provides maximum range without dropout; however, depending upon the

particular environment your system is used in, you may need to reduce that range somewhat in

order to eliminate band noise or interference when the transmitter is turned off. To do so, use

the provided screwdriver to rotate the Squelch control completely counterclockwise (to the “Min”

position), then slowly turn it clockwise until the noise disappears. If no noise is present at any

position, leave it at its fully counterclockwise “Min” position (so as to have the greatest overall

range available).

13. When first setting up the Stage 5 Series System in a new environment, it’s always a good idea

to do a walkaround in order to make sure that coverage is provided for your entire performance

area. Accordingly, turn down the level of your audio system and turn on both the transmitter

and receiver. Then, with the transmitter unmuted, restore the level of your audio system and

while speaking or singing, walk through the entire area that will need to be covered. As you do

so, the “TX” LED on the front panel of the SR5 should always remain lit. Always try to minimize

the distance between transmitter and receiver as much as possible so that the strongest

possible signal is received from all planned transmission points. In fixed installations such as

A/V or corporate conference rooms or for extended range applications (where the transmitter

and receiver are more than 150 feet apart), it may be desirable to angle the receiver antenna

differently from its vertical position or to install the receiver in the same room as the transmitters

(and, if necessary, to extend the wiring to remote audio equipment).

If you have followed all the steps above and are experiencing difficulties, contact your local

distributor or, if purchased in the United States, call Samson Technical Support (1-800-372-6766)

between 9 AM and 5 PM EST.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samson Stage 5H Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info