Bedienungsanleitung Samson SXD3000 (Seite 9 von 16) (Englisch)

629749

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

SXD Series Power Ampliﬁers with DSP

Getting Started - DSP

The SXD power ampliﬁer features sophisticated high-performance DSP with control for the input and output routing, ﬁlter

network, EQ, limiter, and time alignment delay. Follow these steps to navigate through the SXD internal DSP settings:

1. Turn the SXD power ON. The startup screen will be displayed (ﬁgure 1).

2. Press the UP & DOWN buttons to step through the DSP parameters (ﬁgure 2).

3. Rotate the EDIT knob to adjust settings. A box will ﬂash in the upper right corner when a set-

ting has been changed (ﬁgure 3).

4. Press the EDIT button to conﬁrm and set the changes. Press any other button to cancel the

adjustment.

5. Press the BACK button to exit out of a parameter and return to the top level of the menu.

DSP Settings

Preset - Choose either Manual Mode, which provides access to the full set of adjustable parameters, or from the four speak-

er presets: 2 full range, Mono 2-way, Sub/Sat, or 2 subs.

I/O - The I/O screen adjusts the settings for how the inputs will be routed through the DSP to the output connectors.

Stereo: Ch A Input -> Ch A Output & Ch B Input -> Ch B Output

Mono A+B dual: Ch A and Ch B inputs are mixed together, each level control adjusts the corresponding output level

Mono A+B link: Ch A and Ch B inputs are mixed together, Ch A level control adjusts both Ch A and Ch B output levels

Parallel A dual: Ch A input is sent to both Ch A and Ch B outputs, each level control adjust the corresponding output level

Parallel A link: Ch A input is sent to both Ch A and Ch B outputs, CH A level control adjusts the output level for both chan-

nels.

Filter (Manual mode) - The ﬁlter section allows you to build you own crossover or add speaker protection by stetting the

ﬁlters to remove the upper and lower limits of the audio bandwidth.

Filter Ch A - Press the Edit button to enter the ﬁlter parameters for channel A.

Filter Ch B - Press the Edit button to enter the ﬁlter parameters for channel B. If the Ch A ﬁlter is On, then the Ch B ﬁlter

can be set to the same settings by choosing A=B

LPF Freq - Rotate the EDIT knob to adjust the low pass ﬁlter frequency.

LPF Slope - Rotate the EDIT knob to adjust the ﬁlter type and slope roll off in dB per octave.

HPF Freq - Rotate the EDIT knob to adjust the high pass ﬁlter frequency.

HPF Slope - Rotate the EDIT knob to adjust the ﬁlter type and slope roll off in dB per octave.

X-Over (speaker preset) - When using a speaker preset, the ﬁlters are already conﬁgured for a crossover. This allows you to

easily set the crossover frequency for your speaker conﬁguration.

Gain Offset (Manual mode) - This adjustment allows you to set an overall balance between the outputs of the ampliﬁer. This

allows you to match the difference of output level of the speakers in a system without needing to constantly adjust the front

panel level controls.

GAIN OFFSET EQ LIMITERFILTER DELAY SETUPI/O

PRESET

DSP Flowchart

Samson

SXD7000

ﬁgure 1

I/O

Parallel A link

ﬁgure 3

ﬁgure 2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samson SXD3000 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info