Bedienungsanleitung Samson Wireless System Manager for Windows 95 (Seite 17 von 19) (Englisch)

630073

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

Time Domain Mode / Spectrum Analyze Mode

At any time, you can opt to graph different parameters for the selected receiver, or to view the data for a

different receiver altogether, simply by calling up the Time Domain Configuration dialog again. To

determine the actual time of any point in the graph, simply move the cursor to that point and click. A light

gray vertical line will appear at that point and the time display in the upper right-hand corner of the screen

will show the time (in hours/minutes/seconds) of the selected point.

You can also zoom the display in or out to view specific areas of the data. The simplest method of zoom-

ing in is to simply use the mouse to specify the data you want to view: Position the mouse at the start of

the area you want to view, click and hold, then drag across the screen to the end of the area you want to

view. When you then release the mouse, the specified area will zoom in to fill the entire screen. To

restore the screen to its previous condition, simply right-click the mouse.

Alternatively, you can set various screen

magnifications by using the Zoom Tools, available

only in Time Domain Mode. These allow you to

magnify the screen by factors of 2, 5, 10, 20, 50, or

100. To return the screen to standard magnification,

simply click on the “x 1” box. You can make the same

changes to screen magnification by opening the Zoom

menu, available only in Time Domain Mode.

Spectrum Analyze Mode

The third, and final main mode of operation offered by WSM is Spectrum Analyze Mode. In this mode,

WSM uses your connected receivers to scan through all available frequencies and then graphs out the

relative RF signal strengths onscreen. This allows you to make the best channel selections, based on

actual RF conditions in the performance environment of your wireless system.

To enter Spectrum Analyze Mode, either select it from the Window menu, or click on the Spectrum

Analyze icon in the Tool Bar.

In this mode, a scan and spectrum analysis can be run of all standard UR6D frequencies,

of all “X” UR6DX frequencies, or both sets of frequencies. If all receivers in your wireless

system use the same frequencies (that is, if the system contains

all

UR6D receivers or

all

UR6DX receivers), WSM will automatically scan

only those frequencies. However, if your

wireless system contains

both

UR6D and

UR6DX receivers being used simultaneously,

you need to let WSM know which frequencies

you want scanned and analyzed. To do so, call

up the Group Select dialog either by opening the

Setting menu or by clicking on the Group Select

icon in the Tool Bar. In this dialog (shown at left),

you can choose the frequency range (standard

“B Type” UR6D frequencies or “AX Type ” UR6DX

“X” frequencies) you wish to analyze and specify

the receiver you wish to use for scanning purposes.

Zoom Tools

Spectrum

Analyze Mode

icon

Group Select

icon

Spectrum Analyze Mode

Setting menu

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samson Wireless System Manager for Windows 95 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info