Bedienungsanleitung Samson XML910 (Seite 7 von 32) (Englisch)

629984

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Owner's Manual

XML POWERED MIXERS

Input Channel Section

The following section details each part of the XML’s INPUT CHANNELS including the 3-BAND EQ, the MONITOR and EFX

sends, GAIN and VOLUME controls.

Controls and Functions

1. Peak - This LED indicator will ash RED when the channel input signal peaks.

To reduce distortion, turn the VOL control counterclockwise until the clip

indicator does not light during normal use.

2. Equalizer (HF, MF, and LF) - This three-band equalizer allows you to contour

a channel’s high, mid, and low frequency bands. When the control is set to

the 12 o'clock (detent) position, there is no eect on the signal. Turning the

controls fully clockwise will raise the level of the frequency band +15 dB,

while turning the controls fully counterclockwise will lower the level of the

frequency band -15 dB.

3. AUX 1/MON - The AUX 1 controls the amount of signal sent to the Monitor

bus. The AUX 1 send is pre-fader so the signal is unaffected by the position

of the VOL control. These sends are usually used to create a separate mix for

a monitor system. The Monitor bus signal is routed to the front panel MONI-

TOR jack, and may be routed to the SPEAKER RIGHT/MONITOR output jacks,

depending on the setting of the MODE switch. When the MON send knob is at

the 12 o’clock center position, the signal is routed with unity.

4. AUX 2/EFX - The AUX2/EFX send knob allows you to route the signal to the

internal digital eects processor and the EFX 2 SEND output. The AUX2/EFX

send is post-fader so the level of the signal is determined by the position

of the channel Volume control. When the AUX2/EFX send knob is at the 12

o’clock position, the signal is routed with unity.

5. VOL - This knob controls the volume of channel inputs and is used to continu-

ously adjust the loudness of the various signals being blended together at

the Main Outputs. Moving the knob counterclockwise causes the signal to be

attenuated. Conversely, when rotated clockwise, the signal is boosted.

NOTE: For best signal-to-noise ratio, all VOL controls for channels carrying

signal should generally be kept at or near the 12 o’clock (unity) position.

Channels that are unused should have their Volume controls kept fully coun-

terclockwise at their minimum level.

6. COMP (XML610 and XML910 only) - The COMP knob adjusts the level of

compression applied to the channel. As the COMP knob is turned clockwise,

the compression ratio is raised and the output gain is adjusted accordingly.

The dynamic range of the channel is narrowed, where softer signals will

be magnied and loud signals will be subdued to sit better in the mix. You

should use your ears when adding compression to a signal. Too much com-

pression can create a pumping eect, eliminate all dynamic range, and lead to

feedback.

7. PAD 20 dB switch, Channels 1 to 4 (XML610 and XML910 only) – Use this

switch to match the type of input signal you are supplying. If the PEAK light

of an input continues to light even when the VOL is turned down, depress the

PAD switch . Always turn the VOL completely counterclockwise before press-

ing the PAD switch to avoid damaging your speakers.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samson XML910 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Samson XML910

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info