Bedienungsanleitung Samson ZM125 (Seite 13 von 20) (Englisch)

629822

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Operating The ZM Series

Pre Announcement Chime

The ZM series mixer offers a useful Chime function to alert

listeners of an upcoming page. Simply press the front panel

Chime switch to play the chime.

In addition, the ZM series mixer can be set for one of four

selectable Chime tones by moving the internal shorting

jumpers as show in the figure below:

Priority Control

Channel 1 and 2 can be set for Priority operation. When

microphone channel 1 and 2’s Priority switch is set to the “ON”

position, the other input channels will mute whenever signal

is present on the microphones connected to Channel 1 and 2.

Priority Mic Muting

In addition to the priority muting on microphones connected

to Channels 1 and 2, there are three levels of priority muting

which is always active. The priority muting is set in three

groups in the following order.

Chime and Tele page

Remote Mic

Channels 1 through 6

This means if there is a Tele-page or the Chime switch is

pressed, the Remote Mic and input Channels 1 through 6

are muted. If there is a signal on the Remote Mic, Channel

1 through 6 will be muted. The signals in the same priority

group will stay on together.

Connecting the Input Sources

Next, make the signal input connections, using the Euroblock

input connectors on the rear panel. If your mixer has balanced

outputs, we recommend the use of three-conductor cabling

and connectors (unbalanced two-conductor connections

can also be used, but you’ll get better signal quality and less

outside noise and hum if you use balanced lines).

On the front panel of the ZM Series, turn all the Channel input

controls fully counterclockwise (to their “MIN” setting). Then

connect the supplied heavy-gauge 3-pin “IEC” cable to the rear

panel IEC connector and to any grounded AC socket.

Press the front panel Power switch in order to turn on the ZM

Series. The Power LED will light and the Protection LED will go

on. After approximately five seconds, the Protection LED will

go off (you’ll hear a click when this occurs).

Apply an input signal to the ZM Series at or about +4dBu. Now

set the channel level to about half way up.

While the input signal is present, slowly raise the Master level

control until the desired sound level is achieved.

The SIGNAL and PEAK LED indicators will show you the

continuous power output of the ZM Series as signal is being

passed. For the best signal-to-noise ratio, the ZM Series

should normally be run with the Master level control at or

near maximum (fully clockwise, at the “MAX” position) and the

PEAK segments should light occasionally (but not frequently)

during peak levels. If the signal is too loud, use the Input level

controls attenuate the signals as necessary to achieve the

desired speaker level.

CD Player

Microphones

MIN MAX

ON OFF

PRIORITY

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samson ZM125 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Samson ZM125

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info