Bedienungsanleitung Samsung AR07FSFP Series (Seite 32 von 47) (Englisch)

684515

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

Wall

<20mm

Plastic

Anchor

Fixing the installation plate

2. Fix the indoor unit.

If you  x the indoor unit on a wall

(1) Fix the installation plate to the wall giving attention to the weight of the indoor unit.

If you  x the indoor unit on a window frame

(1) Determine the positions of the wooden uprights to be

attached to the window frame.

(2) Attach the wooden uprights to the window frame giving

attention to the weight of the indoor unit.

(3) Attach the installation plate to the wooden upright using

tapping screws.

If you  x the indoor unit on a gypsum board

(1) Use stud  nder to  nd out locations of the studs.

(2) Fix the plate hanger on two studs.

• Ifyoumounttheplatetoaconcretewallusingplasticanchors,makesurethatgaps

between the wall and the plate, created by projected anchor, is less than 20mm.

• Searchforotherspotsiftherearelessthantwostuds,orthedistancebetweenthestudsaredierentfromthe

plate hanger.

• Fixtheinstallationplatewithoutincliningtooneside.

• Makesurethatawallcanwithstandtheweightoftheproduct.Ifyouinstalltheproductinaplacewhereitisnot

strong enough to withstand the product weight, the unit could fall and cause injury.

Connecting the assembly cable

• Connectthepowercableto

the auxiliary circuit breaker. If

every pole fails to connect to

the power supply, it must be

incorporated in a wire with a

contact opening of ≥3mm.

Model Power cable Interconnection cable

Type GL

AR09/12FSFP

3G, 2.5mm

² H07RN-F

3G, 1.5mm² H07RN-F

20A

2* 0.75mm

² H05RN-F

AR18/24FSFP

3G, 2.5mm

² H07RN-F

3G, 1.5mm² H07RN-F

25A

2* 0.75mm

² H05RN-F

Cable speci cation

Connecting the cable

If using a multi system, install as described in the installation manual supplied with the outdoor unit.

Electrical work

(1) For electrical and earth works, comply with the ‘technical standards of electrical installations’ and the the wiring

regulations’ of the Electricity Enterprises Act.

(2) Tighten the terminal block screw to under 12kgf.cm.

(3) Precautions when connecting terminal blocks of the indoor unit



Before connecting, make sure the connecting part of the terminal socket is facing upwards.

Upside down

The terminal

socketis damaged.

There is no ring

terminalto cover the wire.



There must be no space between the terminal and the screw when connected.

- Any remaining space may become a  re hazard due to overheating of the electrical contact.

The terminal socket is

upside down.

Either the screw is not fitted

properly or there is a space between

the screw and the ring terminal.

•

For the terminal block wiring, use a wire with a ring terminal socket only.

Regular wires without a ring terminal socket may become a  re hazard due to overheating of the electrical contact during a wiring work.

Maldives ET_AR09FSFP@_IBIM_DB68-03376A_EN_2.indd 32 2012-12-3 18:54:50

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samsung AR07FSFP Series Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info