Bedienungsanleitung Samsung HDC9D90UG (Seite 30 von 84) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

517128

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

- 30 -

the decorative ue. If your appliance is to be installed in the

ducting version or in the version with external motor, prepare

the air exhaust opening. Adjust the width of the support

bracket of the upper ue (Fig.4). Then x it to the ceiling using

the screws A (Fig.4) in such a way that it is in line with your

hood and respecting the distance from the ceiling indicated

in Fig.2. Connect the ange C to the air exhaust hole using a

connection pipe (Fig.5). Insert the upper ue into the lower

ue. Fix the lower ue to the hood using the screws B provided

(Fig.5), extract the upper ue up to the bracket and x it with

the screws B (Fig.4). To transform the hood from a ducting

version into a ltering version, ask your dealer for the charcoal

lters and follow the installation instructions.

•Filteringversion:

Install the hood and the two flues as described in the

paragraph for installation of the hood in ducting version. To

assemble the ltering ue refer to the instructions contained

in the kit. If the kit is not provided, order it from your dealer

as accessory. The lters must be applied to the suction unit

positioned inside the hood. They must be centred by turning

them 90 degrees until the stop catch is tripped (Fig.8).

USE AND MAINTENANCE

• We recommend that the cooker hood is switched on before

any food is cooked. We also recommend that the appliance is

left running for 15 minutes after the food is cooked, in order

to thoroughly eliminate all contaminated air.

The eective performance of the cooker hood depends on

constant maintenance; the anti-grease lter and the active

carbon lter both require special attention.

•Theanti-greaselter is used to trap any grease particles

suspended in the air, therefore is subject to saturation (the

time it takes for the lter to become saturated depends on

the way in which the appliance is used).

- To prevent potential re hazards, the anti-grease lters

should be washed a minimum of every 2 months (it is pos-

sible to use the dishwasher for this task).

- After a few washes, the colour of the lters may change.

This does not mean they have to be replaced.

If the replacement and washing instructions are not fol-

lowed, the anti-grease lters may present a re hazard.

•Theactivecarbonlters are used to purify the air which

is released back into the room. The lters are not washable

or re-usable and must be replaced at least once every four

months. The active carbon lter saturation level depends on

the frequency with which the appliance is used, the type of

cooking performed and the regularity with which the anti-

grease lters are cleaned.

• Clean the cooker hood frequently, both inside and outside,

using a cloth which has been dampened with denatured al-

cohol or neutral, non-abrasive liquid detergents.

• The light on the cooker hood is designed for use during

cooking and not for general room illumination. Extended

use of the light reduces the average duration of the bulb.

•Replacinghalogenlightbulbs(Fig.6):

To replace the halogen light bulbs B, remove the glass pane

C using a lever action on the relevant cracks.

Replace the bulbs with new ones of the same type.

Caution: do not touch the light bulb with bare hands.

•Commands(Fig.9):

Push-button A = On/o lights switch.

Push-button B = On/o cooker hood switch. The appliance

switches on at speed level 1, If the cooker hood is on depress

the push-button for 2 sec. to switch o the cooker hood. If

the cooker hood is at speed level 1 it will not be necessary

to depress the push-button to switch the cooker hood o.

Decreases the motor speed.

Display C = Indicates the motor speed level selected and

activates the timer.

Push-button D = Switches on the cooker hood. Increases the

motor speed. Touching the key at 3rd speed, the intensive

function runs for 10’, then the appliance go back to work at

the original speed. During this function the display blinks.

Key E = The Timer times the functions on activation for 15

minutes, after which they are switched o. The Timer is deac-

tivated by re-pressing Key E. When the Timer is activated the

decimal point must ash on the display. The Timer cannot be

activated if the intensive speed is functioning.

The “clean air” function is activated by pressing key E for 2

seconds when the appliance is switched o. This switches the

motor on for 10 minutes every hour at the rst speed. During

functioning a rotary movement of the peripheral segments

must be visualised on the display. When this time has passed

the motor switches o and the xed letter “C” must be visual-

ised on the display until the motor re-starts after 50 minutes

for another 10 minutes and so on. Press any key apart from

the light keys to return to normal functioning. Press key E to

deactivate the function.

•Activecarbon/greaseltersaturation:

- When display item C ashes, at a speed where it alternates

with the letter F (e.g. 1 and F), the grease lters must be

washed.

- When display item C ashes, at a speed where it alternates

with the letter A (e.g. 1 and A), the carbon lters must be

replaced.

After the clean filter has been positioned correctly, the

electronic memory must be reset by pressing button A for

approximately 5 seconds, until the indication F or A shown

on the display C stops ashing.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY

FOR EVENTUAL DAMAGES CAUSED BY BREACHING THE

ABOVE WARNINGS.

Samsung HDC9D90UG Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info