Bedienungsanleitung Samsung HW-Q900A (Seite 15 von 35) (Englisch)

804957

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

ENG - 15

LED Status Description Resolution

Red and blue

Blinking Malfunction See the contact information for the Samsung Service

Centre in this manual.

NOTE

• If the main unit is powered off, the wireless subwoofer will go into stand-by mode and the STANDBY LED on the rear of the sub-woofer will

turn red after blinking in blue several times.

• If you use a device that uses the same frequency as the Soundbar near the Soundbar, interference may cause some sound interruption.

• The maximum transmission distance of the main unit’s wireless signal is about 10 m, but may vary depending on your operating environment.

If a steel-concrete or metallic wall is between the main unit and the wireless subwoofer, the system may not operate at all because the

wireless signal cannot penetrate metal.

CAUTION

• Wireless receiving antennas are built into the wireless subwoofer. Keep the unit away from water and moisture.

• For optimal listening performance, make sure that the area around the wireless subwoofer and the Wireless Receiver Module (sold separately)

is clear of any obstructions.

Auto EQ

The Auto EQ technology of Samsung provides more natural and softer bass by calibrating low frequency detected via the mic on the subwoofer.

Low frequency usually occurs due to the size of the room and the location of the subwoofer.

• Ensure the subwoofer is placed at least 8 cm away from walls, furniture or other partitions.

• You must keep the room as quiet as possible while operating the Auto EQ tuning.

• Do not use any buttons until the Auto EQ tuning is complete.

• Auto EQ tuning takes about 2 minutes.

• During Auto EQ tuning, there is no sound from the Soundbar’s main unit and rear speakers.

If you are using the function for the rst time

1. Press the (Sound Control) button until Auto EQ is selected.

2. Press the Up/Down buttons to select Tuning, and then press the button.

3. Tuning will start, and the progress appears in percentage.

‒ To cancel tuning, press the Up, Down, Left, Right or button, and then press the button to conrm.

‒ If the tuning is failed, LED blinks in red.

‒ If the tuning is successful, LED blinks in blue.

If you have done the tuning process

1. Press the (Sound Control) button until Auto EQ is selected.

2. Press the Up/Down buttons to select Tuning, and then press the button.

3. Press the Up/Down buttons to select one of the following options.

‒ On: Turn on the previously tuned EQ settings.

‒ Off: Turn on the default EQ settings.

‒ Tuning: Start the tuning process again.

Connecting an SWA-9500S (Sold Separately) to your Soundbar

Expand to true wireless surround sound by connecting the Samsung Wireless Rear Speaker Kit (SWA-9500S, sold separately) to your Soundbar.

For detailed information on connections, see the Samsung Wireless Rear Speaker Kit manual.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samsung HW-Q900A Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Samsung HW-Q900A

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info