Bedienungsanleitung Samsung ML-6510 (Seite 48 von 130) (Englisch)

586979

Zoom out

Zoom in

Vorherige Seite

1/130

Nächste Seite

Media and tray_ 48

fusing temperature about 170°C (338 °F) for 0.1 second. The extra flaps

and strips might cause wrinkling, creasing, or jams and may even dam-

age the fuser.

• For the best print quality, posi

tion margins no closer than 15 mm from

the edges of the envelope.

• Avo

id printing over the area where the envelope’s seams meet.

Transparency

To avoid damaging the machine, use only transparencies designed for use

in laser printers.

• Transparencies used in the machine must be able to withstand

machine’s fusing temperature.

• Place them on a flat surface after removing them from the machine.

• Do not leave unused transparencies in the paper tray for long periods of

me. Dust and dirt may accumulate on them, resulting in spotty printing.

• To avo

id smudging caused by fingerprints, handle them carefully.

• To avoid fading, do not expose printed transparencies to prolonged sun-

light.

• Ensure

that transp

arencies are not wrinkled, curled, or have any torn

edges.

• Do not use transparencies that separates from the backing sheet.

• To prevent transparencies from sticking to each other, do not let the

rinted sheets stack up as they are begin printed out.

• Base

type transparency (ex. Xerox 3R3117) results in better image and

pap

er handling quality than paper backed (ex. Xerox 3R3028) or remov-

able stripe (3R3108) ones.

Depending on the selection or storage conditions of the transpar-

ency, jam or image scratch might occur.

Labels

To avoid damaging the machine, use only labels designed for use in laser

machines.

• When selecting labels, consider the following factors:

- Adhesives: Th

e adhesive material should be stable at your

machine’s fusing temperature about 170°C (338 °F).

- Arra

ngement: Onl

y use labels with no exposed backing between

them. Labels can peel off sheets that have spaces between the

labels, causing serious jams.

- Curl: Prior to

printing, labels must lie flat with no more than 13 mm

of curl in any direction.

- Co

ndition: D

o not use labels with wrinkles, bubbles, or other indica-

tions of separation.

• Do not use labels with slick back.

• Do not use partially used labels.

• Do not use the labels with separated edges.

• Make sure that there is no exposed adhesive material between labels.

Exp

osed areas can cause labels to peel off during printing, which can

cause paper jams. Exposed adhesive can also cause damage to

machine components.

• D

o not run a sheet of labels through the machine more than once. The

dhesive backing is designed for only a single pass through the

machine.

• D

o not use labels that are separating from the backing sheet or are wrin-

kled, bubbled, or otherwise damaged.

Card stock/Custom-sized paper

• Do not print on media smaller than 76.2 mm (3 inches) wide or 127 mm

(5 inches) long.

• In the software application, set margins at least 6.4 mm (0.25 inches)

away from the edges of the material.

• U

sable minimum weight of 3*5 inches paper is 105g/m². (28 lbs bond)

• Ensure that 76.2 mm (3 inches) X 127 mm (5 inches) is not curled or has

no torn edges. Depending on the curl of 76.2 mm (3 inches) X 127 mm

inches) paper, jam might occur.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samsung ML-6510 Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Samsung ML-6510

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info