Bedienungsanleitung Samsung NK86NOV9MSR (Seite 25 von 69) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

580859

Zoom out

Zoom in

Vorherige Seite

1/69

Nächste Seite

- 25 -

- Make sure that the 2 levelling screws D are not tightened;

Fig. 4 - stage 2.a.

- Take the hood, tilt it and hook it on to the bracket as shown

in Fig. 4 - stage 1.

- Once the structure has been positioned, secure it to the

bracket by coupling the nut with the screw; Fig. 4 - stage 2.

- Tighten the nut with a spanner, leaving a gap of at least 3 mm

between the nut and the bracket as shown in Fig. 4 - stage 3.

Align the appliance horizontally using the two levelling screws

D Fig. 5 - stage 1.

- Once the adjustment is complete, t the hood in a permanent

manner with the screws B and nuts C Fig. 5 - stage 2 and 3.

- When carrying out the xing operations, use only screws

and screw anchors suited to the type of wall (e.g. reinforced

concrete, plasterboard etc.).

If the screws and screw anchors are supplied with the appli-

ance, make sure that they are suited to the type of wall to

which the hood must be xed.

• Attention!

Before proceeding with the installation of decorative ues t

the electrical system box E.

- Lift the electrical system box; Fig. 6 - stage 1.

Position the bracket E in correspondence of the 3 screws G

already arranged on the bushing and tighten them as shown

in Fig. 6 - stage 2 - 3 - 4.

• Installation of models with decorative ducts - extrac-

tor hood

Make sure the electrical power supply is within the measure-

ments of the decorative connector.

Adjust the width of the support bracket of the top connec-

tor (Fig. 7).

Then x it to the ceiling so that it is on the same axis as the

hood using screws A and observing the distance from the

ceiling shown in (Fig. 7). Connect ange F to the air exhaust

hole using exible hose L (Fig.8).

Take care not to scratch the duct; wear gloves when removing

the protective lm. (Fig. 9)

Slide the top connector inside the lower duct and place this

on the body (Fig. 10).

Pull out the top duct as far as the bracket and secure it using

screws B (Fig. 7).

To transform the hood from a ducting version into a ltering

version, ask your dealer for the charcoal lters and follow the

installation instructions.

• Filtering version:

Install the hood and the two ues as described in the

paragraph for installation of the hood in ducting version. To

assemble the ltering ue refer to the instructions contained

in the kit. If the kit is not provided, order it from your dealer

as accessory. The lters must be applied to the suction unit

positioned inside the hood. They must be centred by turning

them 90 degrees until the stop catch is tripped (Fig. 2- stage 3).

USE AND MAINTENANCE

• We recommend that the cooker hood is switched on before

any food is cooked. We also recommend that the appliance is

left running for 15 minutes after the food is cooked, in order

to thoroughly eliminate all contaminated air.

The eective performance of the cooker hood depends on

constant maintenance; the anti-grease lter and the active

carbon lter (Fig. 2 - stage 3) both require special attention.

• The anti-grease lter is used to trap any grease particles

suspended in the air, therefore is subject to saturation (the

time it takes for the lter to become saturated depends on

the way in which the appliance is used).

- To prevent potential re hazards, the anti-grease lters

should be washed a minimum of every 2 months (it is pos-

sible to use the dishwasher for this task).

- After a few washes, the colour of the lters may change.

This does not mean they have to be replaced.

If the replacement and washing instructions are not fol-

lowed, the anti-grease lters may present a re hazard.

• The active carbon lters are used to purify the air which

is released back into the room. The lters are not washable

or re-usable and must be replaced at least once every four

months. The active carbon lter saturation level depends on

the frequency with which the appliance is used, the type of

cooking performed and the regularity with which the anti-

grease lters are cleaned.

• Clean the cooker hood frequently, both inside and outside,

using a cloth which has been dampened with non-abrasive

liquid detergents.

• The light on the cooker hood is designed for use during

cooking and not for general room illumination. Extended

use of the light reduces the average duration of LED lamp.

• Replacing LED lamps (Fig.11).

If the appliance version is with LED lamps, the intervention of

a specialised technician is necessary to replace them.

• Commands (Fig.12):

- To activate the functions put your hand in front of the sensor

at a distance of no more than 8 cm.

Sensor:

1 - Indicated LED lamp = This lamp is will light on or off when

IRed sensor is detected.

2 - IRed sensor = This sensor emits infrared light when an

electric current passes through it.

3 - Photo transistor = This sensor receive the reflected

infrared signal.

Sensor A = Activate the "ON/OFF" function or the "Cleaning

mode" function.

- ON/OFF

Activates or switches off all functions.

- To activate it place your hand in front of the sensor.

- When the LED switches on the hood functions are ready

to be activated.

Attention! If one interrupts hood operation with the rel-

evant sensor and one does not activate any other function

within 10 minutes, the hood switches OFF automatically.

Therefore, if you wish to restart the hood again, you must

place your hand in front of the sensor A (on/off).

- To disable the function repeat the operation.

- Cleaning Mode

Blocks all functions to prevent switching the product on

accidentally during cleaning operations where are in front

of the hood.

- To activate it put your hand in front of the sensor for ap-

proximately 4 seconds.

- When the LED lights up followed by a multiple sound signal

the function is active.

- To deactivate the function repeat the operation.

Sensor B = Activates the “TIMER” function or the “CLEAN

AIR” function.

- Timer

Samsung NK86NOV9MSR Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info