Bedienungsanleitung Samsung Sam4S SPS-320 (Seite 280 von 291) (Englisch)

630503

280

Zoom out

Zoom in

Vorherige Seite

1/291

Nächste Seite

280 • IRC (Inter-Register Communications) Appendix SAM4s SPS-300 Operator's & Programming Manual v1.4

Ethernet Cable Termination Instructions

1. Pull the cable off the reel to the desired length and cut. If you are pulling cables

through holes, it is easier to attach the RJ-45 plugs after the cable is pulled. The total

length of wire segments between an SPS-2000/SPS-5X0 and a switch or between two

ECRs cannot exceed 100 Meters (328 feet).

2. Start on one end and strip the cable jacket off (about 1") using a stripper or a knife.

Be extra careful not to nick the wires, otherwise you will need to start over.

3. Spread, untwist the pairs, and arrange the wires in the order of the desired cable end.

Flatten the end between your thumb and forefinger. Trim the ends of the wires so

they are even with one another, leaving only 1/2" in wire length. If it is longer than

1/2" it will be out-of-spec and susceptible to crosstalk. Flatten and insure there are no

spaces between wires.

4. Hold the RJ-45 plug with the clip facing down or away from you. Push the wires

firmly into the plug. Inspect each wire is flat even at the front of the plug. Check the

order of the wires. Double check again. Check that the jacket is fitted right against

the stop of the plug. Carefully hold the wire and firmly crimp the RJ-45 with the

crimper.

5. Check the color orientation. Check that the crimped connection is not about to come

apart, and check to see if the wires are flat against the front of the plug. If even one of

these is incorrect, you will have to start over. Test the Ethernet cable.

Ethernet Cable Tips

 A crossover is used to connect two Ethernet devices without a switch.

 A crossover has one end with the Orange set of wires switched with the Green set.

 Odd numbered pins are always striped, even numbered pins are always solid colored.

 Looking at the RJ-45 with the clip facing away from you, Brown is always on the

right, and pin 1 is on the left.

 No more than 1/2" of the Ethernet cable should be untwisted otherwise it will be

susceptible to crosstalk.

 Do not deform, do not bend, do not stretch, do not staple, do not run parallel with

power cables, and do not run Ethernet cables near noise inducing components.

Routing Communication Cable

Communication cable must be kept a minimum of one (1) foot away from AC wiring or

fluorescent lighting and at least five (5) feet away from large transformers or motors. If

the communication cable must cross AC wiring, it must cross at a 90 angle to the AC

wiring.

Metal Conduit should be used wherever there is a chance of damage to the wire

including telephone rooms and basements (where rodents could pose a problem). This

conduit should be attached to the building ground not the isolated ground.

Communications cable must NOT be placed alongside or in the same conduit as AC

power or telephone signals.

The bending radius on CAT 5e UTP or STP cable is to be a minimum of 1 inch.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samsung Sam4S SPS-320 Seite 280

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Samsung Sam4S SPS-320

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info