621369
55
Zoom out
Zoom in
Vorherige Seite
1/147
Nächste Seite
English _55
MAIN MENU
HDD Alarm
You can set alarm settings for HDD defects such as Check Alarm Output Port, Replace Alarm Output Port,
and its duration.
Using the mouse may help make setup easier.
1. Use the up/down buttons (▲▼) in <Device> window to
move to <Storage Device>, and press [ENTER] button.
2. Select <HDD Alarm>.
A window for setting HDD check and replace output ports
and their durations appears.
3. Use direction buttons (▲▼_ +) to move to the desired
item.
•Check Alarm Output Port : If HDD generates check alarm,
the alarm signal will output to the specified alarm output
port.
•Replace Alarm Output Port : If HDD generates replace alarm, the alarm signal will output to the specified
alarm output port.
•Duration : Sets the alarm duration for the alarm signal and beep sound.
- If <BEEP> was selected, a beep will sound.
M
` <Check> status means that the HDD is operating but it has problems that require technical examination.
(
) appears on the Live screen.
` <Replace> status means that the HDD has defect and requires immediate replacement.
(
) appears on the Live screen.
` If the installed HDD is not recognized properly, a confirmation popup will appear.
4. When the HDD Alarm setup is done, press <OK>.
Remote Devices
You can set the RS-485 communication for use of PTZ Camera with the DVR.
Using the mouse may help make setup easier.
1. Use the up/down buttons (▲▼) in <Device> window to
move to <Remote Device>, and press [ENTER] button.
2. Use direction buttons (▲▼_ +) to move to the desired
item, and press [ENTER] button.
3. Set the values of each communication setup of the remote
device.
•Baudrate : Baud rate settings of the DVR, PTZ camera
should be matched for proper operations.
4. Make sure to match IDs of the DVR and Remote Control,
and press <OK>.
M
` For changing the remote control’s ID, refer to “Changing the Remote Control ID”. (Page 15)
Storage Device
Format
OK Cancel
Device
HDD Alarm
Check Alarm Output Port
Duration OFF
BEEP
Replace Alarm Output Port
Duration OFF
BEEP
Remote Control ON ID 0
Baudrate Parity Data Stop Bit Transfer type
9600

None
8

1

Half Duplex
Remote Device
OK Cancel
55

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Samsung SDH-V5100 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info