Bedienungsanleitung Samsung SNV-6085R (Seite 20 von 70) (Englisch)

621307

Zoom out

Zoom in

Vorherige Seite

1/70

Nächste Seite

network connection and setup

20_ network connection and setup

If not using a Broadband Router

For setting <IP Address>, <Subnet Mask>, and <Gateway>, contact your network administrator.

4. In the <Port> pane, provide necessary information.

• HTTP Port : Used to access the camera using the Internet

browser, defaulted to 80.

• VNP Port : Used to control the video signal transfer,

defaulted to 4520.

5. Enter the password.

Enter the password of “admin” account, which was used to

access the camera.

For the security purposes, you are recommended to use a combination of numbers, alphabets uppercase and lowercase and

special characters for your password.

If you want to change the password, refer to “Administrator password change” of the user setup. (page 32)

6. Click [OK].

Manual network setup will be completed.

If using a Broadband Router

• IP Address : Enter an address falling in the IP range provided

by the Broadband Router.

ex) 192.168.1.2~254, 192.168.0.2~254,

192.168.XXX.2~254

• Subnet Mask : The <Subnet Mask> of the Broadband Router

will be the <Subnet Mask> of the camera.

• Gateway : The <Local IP Address> of the Broadband Router

will be the <Gateway> of the camera.

The settings may differ depending on the connected Broadband

Router model.

For more information, refer to the user manual of the applicable router.

For more information about port forwarding of the broadband router, refer to “Port Range Forward (Port Mapping) Setup”.

(Page 21)

If the Broadband Router has more than one camera connected

Configure the IP related settings and the Port related settings distinctly with each other.

ex)

Category Camera #1 Camera #2

IP related settings

IP Address

Subnet Mask

Gateway

192.168.1.100

255.255.255.0

192.168.1.1

192.168.1.101

255.255.255.0

192.168.1.1

Port related settings

HTTP Port

VNP Port

8080

4520

8081

4521

If the <HTTP Port> is set other than 80, you must provide the <Port> number in the address bar of the Internet browser

before you can access the camera.

ex) http://IP address : HTTP Port

http://192.168.1.100:8080

Auto Network Setup

Run <IP Installer_v2.XX.exe> to display the camera search list.

At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.

For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not support this function.

1. Select a camera in the search list.

Check the MAC address of the camera on the camera’s label.

Both the [Auto Set] and [Manual Set] buttons will be

activated.

2. Click [Auto Set].

The Auto Setting dialog appears.

The <IP Address>, <Subnet Mask>, and <Gateway> will

be set automatically.

3. Enter the password.

Enter the password of “admin” account, which was used to

access the camera.

For the security purposes, you are recommended to use a

combination of numbers, alphabets uppercase and lowercase and

special characters for your password.

If you want to change the password, refer to “Administrator

password change” of the user setup. (page 32)

4. Click [OK].

Auto network setup will be completed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samsung SNV-6085R Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info